Jump to content
SAU Community

Recommended Posts

hey there, just wondering if anybody can help me out ?? i have a series 2 rs4. Once the car reaches operating temp on my way to work, the malfunction light comes on, i give it a rev and the light goes off and stays off, approx 45 km's to work. Very rarely does this happen on the way home in arvo.. nissan checked the code and told me most likely a coil fault. Since then i have fitted splitfires and new sparkplugs but still no difference. The car seems to be running fine and i can't notice any misfiring ?? any ideas would be much appreciated !! THANX

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/
Share on other sites

hey there, just wondering if anybody can help me out ?? i have a series 2 rs4. Once the car reaches operating temp on my way to work, the malfunction light comes on, i give it a rev and the light goes off and stays off, approx 45 km's to work. Very rarely does this happen on the way home in arvo.. nissan checked the code and told me most likely a coil fault. Since then i have fitted splitfires and new sparkplugs but still no difference. The car seems to be running fine and i can't notice any misfiring ?? any ideas would be much appreciated !! THANX

check the codes yourself

this will show you which points to bridge

attached page will show you how to do it.

http://www.skylinesaustralia.com/forums/Ex...p;hl=paper+clip

Pages_from_R34_service_man.pdf

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4412411
Share on other sites

I have access to Nissan Data Scan and live nearby. If you're interested we can plug it in & see what comes up after a datalog.

This sounds great BensDR30, can you explain how the data loggin works ?? i am only new to imports as i have spent my years on old skool v8's..

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4413171
Share on other sites

check the codes yourself

this will show you which points to bridge

attached page will show you how to do it.

http://www.skylinesaustralia.com/forums/Ex...p;hl=paper+clip

Pages_from_R34_service_man.pdf

hey there, thanx for the link, but i still couldn't see ne-where that explained how to do this in detail ??

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4413174
Share on other sites

i had the same thing as you, check engine light flash up, give it a little rev and it would go away. when i checked the error codes it was the O2 sensor. but i would have thought nissan would have been able to give you a better idea of what it was when the checked the error codes. the error codes remain on the error code list until you reset them.

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4414720
Share on other sites

i had the same thing as you, check engine light flash up, give it a little rev and it would go away. when i checked the error codes it was the O2 sensor. but i would have thought nissan would have been able to give you a better idea of what it was when the checked the error codes. the error codes remain on the error code list until you reset them.

Yeah, thats why i took it to nissan, but they admitted the had never worked on a stagea and didn't have any code lists to use as a reference... they somehow came up with a coil fault though ??? how would i change the 02 sensor ?? is there only one ??

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4414781
Share on other sites

i wouldn't jump to the conclusion that it is the O2 sensor, i was just saying that i had the same thing with the light flashing up and going away with a rev.

i'd see if someone on here that lives close to you has the consult/datascan software can check you error codes for you, or do the error code thing yourself by bridging the two pins on the consult plug. or just go back to nissan and get them to check the codes.

see what the problem is before spending anymore money replacing parts that may not have anything to do with the problem.

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4414795
Share on other sites

The O2 sensor is located just behind the turbo. It's not a big job, 22mm open-ender (or vise grips) to get the original one out. That bit can take a while, but fitting a new one is only a 5-minute job. There are threads detailing the replacement, but it's a pretty simple task.

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4414797
Share on other sites

The O2 sensor is located just behind the turbo. It's not a big job, 22mm open-ender (or vise grips) to get the original one out. That bit can take a while, but fitting a new one is only a 5-minute job. There are threads detailing the replacement, but it's a pretty simple task.

No worries, i have just read that nissan reccomends o2 sensors are replaced every 40,000km's anyway, so i will change the sensor and see how i go...

thanx heaps for the help guys, will post the result...

Link to comment
https://www.sau.com.au/forums/topic/255854-help-please/#findComment-4414943
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, I'm tired. I'm tired because about 4PM yesterday, before today's appointment someone immediately bought my bumper. They couldn't get it any other day as they're on the way back to NSW. So I had to do that big GTR conversion I had been planning. Unfortunately, the information on SAU about what you need and how this is done is incomplete. So what should be a simple bolt on affair, yeah, it's not. Did you know if you use all GTR items the bonnet won't close? This little manuever sent me into about 1am the night before trying to dodge a way to get it closed. I will have to revisit this in the next few days  - or maybe not, I may let a body shop figure it out. It all needs to come up and my motivation to pull the bumper off is low. It also seems to hit things in the bay where the GTT bonnet didn't. Yes I used 100% new OEM GTR items. Today, I had the joy of driving to the dyno looking like this: Given I had roughed in the fuel and given sensible but pretty conservative timing, I didn't really bet on having the car drive out any real difference than when it drove in. Sadly due to a miscommunication and laptop fun and games (and almost bricking the dongle, prayers and firmware updates indeed), I ended up using HP Tuner credits to licence the car that was already licenced. So in the end my laptop was used. It turns out my butt dyno is still well calibrated after all this time. The 325kw was on 74% Ethanol, the 313kw line was on 98. The other line is the 'before' line which was 281kw. While the numbers are pretty low, they're pretty in line with what you'd expect. Even if US dynos bump the whole result up about 50KW, gaining 10-15% is similar gains.  The curve of the cam is pretty much spot on with what was discussed as well. All this said, it still feels bad to not see the number you secretly want to see. Even if the car drove great beforehand, and I knew pretty confidently the car would drive out much the same way it drove in due to the nature of a wellish dialled in LS1 not gaining much if anything at all from being tuned from where it was. As expected, the car isn't particularly sensitive to running it at anywhere between 12.0 and 13.0 - And the initial timing at 20deg and 12.0 made 308KW. So 3 degrees of timing, and leaning it out to 12.7 for 5kw, anything above stopped giving any benefit until E85 (which has an additional 2 deg as before). Car itself behaved entirely fine. I found out that 100C = 1.15V! IAT at about 7pm was 19C. I might mess with the bonnet mounting.. but given the REO NEEDS TO BE CHOPPED TO FIT A GTR BAR this is possibly something I may leave gathering (more) dust until it returns to paint jail.
    • It sounds farrrrrrr too cold at your place Duncan... Here I was thinking our 10 degrees overnight is getting cold...
    • oh yeah, reminded this morning....bin lids frozen shut too
    • In my case not, because of total reno. But yeah.
    • Did you use an electronic speedo drive? Does you speedometer read all the way to 180km?
×
×
  • Create New...