Jump to content
SAU Community

Recommended Posts

If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

post-51561-1234173000_thumb.jpg

post-51561-1234173013_thumb.jpg

Edited by moneypit
Link to comment
https://www.sau.com.au/forums/topic/256292-r34-mfd-replacement-screen/
Share on other sites

If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

so is this genuine nissan one or after market?

cheers.

so is this genuine nissan one or after market?

cheers.

As far as I know nissan do not sell the screen. They sell the entire MFD for mucho $$$s only.

the MFD is plastic surround and cage and buttons, the MFD circuit board with its various sensor inputs

and the toshiba screen.. this is just the screen.

a little bit off topic but around how much would the real mfd cost approx?

I see a second hand one in pretty poor shape listed at 90,000 yen about to close.

so after fees and expenses that is pretty close to $2000 aud.

and, this screen is the "real" mfd, as in, if you have a busted screen, it is this

screen that is busted.

Just in case people think this is an inferior non oem substitute..

  • 1 month later...
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

Hi i am after a screen and you text me pls 0414959914

Thank you

  • 2 weeks later...
  • 2 weeks later...

If anyone knows where you can get the whole MFD (with casing etc) will buy it off you...or from Nissan itself lmaa i really dont mind spending the money its better than going aftermarket and getting an Alpine screen for example which costs a shitload and doesnt even fit the factory center console on my GT...

There was 2 types of screens used in the GTR mfd, the early models used a Sharp screen, and the late models used a Toshiba screen. (as far as I know there was a supply issue with the Sharp LCD, thats why it got changed.) From what I can figure out the Nismo GTR MFD2 Unit will accept either LCD as there are both the connectors.

Make sure your GTR screen has 2x ribbon cables going to the LCD, a skinny ribbon cable and wide ribbon cable (Toshiba), or if it as 1x 30pin cable it a Sharp screen and will not fit!!

I am currently experimenting with both types of unit and will be putting up an in depth post in future...

Hi Mate,

I've got a 99 34GTR with the annoying white tram lines going through the RHS of the MFD... Can you pls confirm the toshiba screen your selling is a direct replacement for the early model 34 GTR's!

... If so can you pls put me down for one

will PM you

  • 2 weeks later...
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

hi ... i would like to order 2 screens .heat busted mine and my friends. the problem is i cant pm u over here... could u email me on [email protected] .thanks

  • 2 months later...

hi there, just wondering if you have any screens left?

My one is heat damaged and realy sh@#s me. please email me as i can not pm.

thankx heaps.

[email protected]

cheers.

  • 5 months later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...