Jump to content
SAU Community

R34 Mfd Replacement Screen

rtune
 Share

Recommended Posts

rtune Experienced

rtune

Posted
Posted (edited)

If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

post-51561-1234173000_thumb.jpg

post-51561-1234173013_thumb.jpg

Edited by moneypit
Link to comment
https://www.sau.com.au/forums/topic/256292-r34-mfd-replacement-screen/
Share on other sites
sun33 Community Regular

sun33

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

so is this genuine nissan one or after market?

cheers.

rtune Experienced

rtune

Posted
  • Author
Posted
so is this genuine nissan one or after market?

cheers.

As far as I know nissan do not sell the screen. They sell the entire MFD for mucho $$$s only.

the MFD is plastic surround and cage and buttons, the MFD circuit board with its various sensor inputs

and the toshiba screen.. this is just the screen.

rtune Experienced

rtune

Posted
  • Author
Posted
a little bit off topic but around how much would the real mfd cost approx?

I see a second hand one in pretty poor shape listed at 90,000 yen about to close.

so after fees and expenses that is pretty close to $2000 aud.

and, this screen is the "real" mfd, as in, if you have a busted screen, it is this

screen that is busted.

Just in case people think this is an inferior non oem substitute..

  • 1 month later...
BOBBYr34 Experienced

BOBBYr34

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

Hi i am after a screen and you text me pls 0414959914

Thank you

  • 2 weeks later...
  • 2 weeks later...
CR34M Community Regular

CR34M

Posted
Posted

If anyone knows where you can get the whole MFD (with casing etc) will buy it off you...or from Nissan itself lmaa i really dont mind spending the money its better than going aftermarket and getting an Alpine screen for example which costs a shitload and doesnt even fit the factory center console on my GT...

Adrian P Community Regular

Adrian P

Posted
Posted

There was 2 types of screens used in the GTR mfd, the early models used a Sharp screen, and the late models used a Toshiba screen. (as far as I know there was a supply issue with the Sharp LCD, thats why it got changed.) From what I can figure out the Nismo GTR MFD2 Unit will accept either LCD as there are both the connectors.

Make sure your GTR screen has 2x ribbon cables going to the LCD, a skinny ribbon cable and wide ribbon cable (Toshiba), or if it as 1x 30pin cable it a Sharp screen and will not fit!!

I am currently experimenting with both types of unit and will be putting up an in depth post in future...

fantov Enthusiast

fantov

Posted
Posted

Hi Mate,

I've got a 99 34GTR with the annoying white tram lines going through the RHS of the MFD... Can you pls confirm the toshiba screen your selling is a direct replacement for the early model 34 GTR's!

... If so can you pls put me down for one

will PM you

  • 2 weeks later...
uae810 Newbie

uae810

Posted
Posted
If you have a problem with your MFD LCD screen (busted scan lines, bad backlight, bad pixels),

then replace it with this fresh new one. I've done it. I can verify that replacing it with this panel

works great. Requires removal of MFD, and careful dis-assembly of MFD, connect two ribbon cables,

and re-assembly. Takes just 10 minutes and a screwdriver.

$200 plus $9.99 shipping bubble wrapped in anti-static foam.

hi ... i would like to order 2 screens .heat busted mine and my friends. the problem is i cant pm u over here... could u email me on [email protected] .thanks

  • 2 months later...
mole34 Apprentice

mole34

Posted
Posted

hi there, just wondering if you have any screens left?

My one is heat damaged and realy sh@#s me. please email me as i can not pm.

thankx heaps.

[email protected]

cheers.

  • 5 months later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Pac
      Returning after a long time!

      By Pac · Posted

      Welcome back mate ,I also joined in the early 2000's , since then I have been in and out a few times depending if I had a skyline in the garage.  I have the another one now , so signed up and back with the SAU team.
    • Lithium
      Upgrade an rb25neo

      By Lithium · Posted

      I used "different strokes for different folks" quite pointedly as honestly, there is no wrong when it comes to choosing what you like.  I always day dreamed about flappy paddles with fast shifts in a sporty RWD Turbo and to me the sound and feel of it cutting through gears in a steady stream is exciting, engaging, and keeps the car better balanced - I *also* like h-patterns, but I find them more engaging and fun in a nice hoonable peaky NA thing.  Type-R Integra/old school NA rotary, things that are raw and need all the rpm where picking the gear and getting it sky high is part of the engagement of the whole thing despite the fact that they probably need closer ratios and faster shifts even more than a 3l turbo thing haha  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      If I wasn't allowed or really had the desire to visit China it would probably fit in my carry on, but I have no desire, Japan would be nice during Cherry Blossom time though I might need to chat to Jackie about that, that should actually be an easy conversation though as she is currently talking about another cruise, cruise ship to Japan, a week in Japan to see the sights, then cruise home I may even be able to find those OEM NC Recaro seats over there that I cannot find here 🤔
    • Lithium
      Garrett G Series

      By Lithium · Posted

      What do you mean?  In between the two I shared?  They're the same boost   This will be insane.   A mate has a GTSt with a 9:1 RB30/25 with Tomei 256 cams and a Borg S362SX-E that is already a beast from the basement but has a stock 5 speed and will probably get a ZF8 one day.  After the G35 900 RB26 setup I'd be lying if the topic of "Wtf would a divided G35 be like on this thing?" idea hadn't come up - you'd definitely want a wide boost control range setup with it, as even with the less responsive and potent S361 we're having to ramp boost in from very low levels in the early gears.
    • joshuaho96
      Upgrade an rb25neo

      By joshuaho96 · Posted

      ZF8 is faster, wider ratio spread, better in every way. I do not dispute this. But I have brain damage and I want the feeling of shifting gears. To me the extra work is fun, but I daily an automatic and in the US like 90+% of cars are automatic so a manual transmission is an "exotic" experience. If I want an automatic I've driven an F80 M3 with DCT more than a few times and it's incredibly capable but it's emotionally vacant to me.
×
×
  • Create New...