Jump to content
SAU Community

Recommended Posts

Engine:

N1 24U block (own modifications done) race prepped

Fully balanced and blue printed

Chemically cleaned/crack tested and washed

Torque plate bored honed & decked

All new welsh plugs

Tapped oil gallaries

Fully balanced/detailed crank and grub screwed

New Ross harmonic ballancer

Race prepped crank gurdle

Shot peened/prepped standard rods with ARP bolts

Full ARP bottem end stud kit

Ross Racing forged pistons (ceramic coated)

ACL race bearings mains & rods

N1 oil pump (modified)

N1 water pump

Genuine Nissan gasket kit

Fully port & polished head

Match ported intake

Brass valve guids

Standard valves

Upgrade valve springs

Standard cams

Greddy adjustable cam gears

Gates timing belt

New genuine exhaust studs & nuts

Garrett GT3082r .82 turbo polished front cover

Braided oil lines

Speedflow fittings

Tial 44mm wastage

Ebay spec manifold modified

Greddy twin entry air intake pipe

2 x RB25 Air flow meters

4" dump pipe

4" catback exhaust

4” high flow ballistic cat

600x300x115mm Greddy style intercooler

Custom PBR clutch

Nismo lightened flywheel

Nistune ECU

Sard fuel pressure regulator

custom fuel rail

r33 gtr lift pump

044 fuel pump

2L surg tank

3/8" Aluminium fuel lines

Heap of speed flow fittings & push lock hose

Sard 700cc injectors

Alloy dual core radiator

Silicone radiator hoses

Silicone heater hoses

Exterior:

Full colour change

18x9 18x10 roh drift r's

carbon exhaust shroud

carbon top secret bonnet painted

genuine gtr front bar and gtr grill

rear drift lip

nismo b pillars

tein coil overs

Inerior:

gtr dash cluster

autometre boost guage

hybrid boost controller

greddy turbo timer

Link to comment
https://www.sau.com.au/forums/topic/256366-final-stages-d/#findComment-4420116
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...