Jump to content
SAU Community

Recommended Posts

Hello,

i kinda need someones help on this one, i misplaced my Log Book recently and i cannot find it at all! :( Does anyone know wher i can find a proper blank service log book for any Vehicle in Australia? I own a 350GT Coupe if i find proper one for it will be better, but as for now anything will do... i went to Autobarn or Super Cheap Auto, they do not provide spare log books... can anyone share a light to me on this case pls?

Thank you in advance.

One last question, I plan to change the braking system on my Coupe, i was adviced to get the front ones changed first and i can probably do the rear ones later on as 70% of the time (braking) the front one does the work... Would this make any difference in my/our case since the car is a rear wheel drive?

Thanks again! Peace!

Link to comment
https://www.sau.com.au/forums/topic/256735-help-with-2-questions/
Share on other sites

If you want to keep a record of your servicing just keep a folder of all the receipts. I take more stock in these than a stamped book. I quite sure that even the manufacturer wouldn't provide your with new service books, and you can't have mine :(

As for your brakes, your front ones are doing most of the work 100% of the time. I assume you don't have Brembo's so that would be simplest upgrade. Keep your eye's out for some v35/GTR Brembo's.

true, braking is mostly due to weight transfer, being FWD or RWD have less effect.

however when increasing the size of the brakes, I found most FWD kit will only provide bigger brakes for the front, and not to the rears. reason is because FWD cars have no powers going to the rear and increasing the rear rotor size may cause a lockup and could be dangerous.

On the contrary, AWD and RWD big brake kits are usually available for both front and rear, and recommended to increase the rotor size both front and back at the same time, although for V35 Nismo creates a 355mm front brake upgrade with F50 brembos that can be fitted to V35 with brembo 324mm, without upgrading existing rear 322mm.

Though, non brembo owners were strongly advised to upgrade rear non-brembo brakes from 292mm to 322mm brembo ones before fitting the Nismo big brake kit. otherwise it won't be balanced. But at this economic situation, it will be very expensive to buy this big brake kit from Japan. It used to cost like $6k delivered when Aus was 86JPY now I dare not to calculate. probably $10k.

Best upgrade if you want bigger size is to find 350Z brembo or G35 brembo from USA. This is straight fit, but be wary of the shipping cost and exchange rate. Plus if you swap to bigger brake size and caliper, your spare wheel won't fit. You need to buy 350Z track brembo spare wheel from Nissan. Not sure how much they'll charge for that. I am yet to make an enquiries to Nissan about it.

Have anyone tried R33/R34 GTR brembo kit if they'll fit a V35? However the R33 GTR colour will be black so it doesn't look 'right'.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...