Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

I thought i would make a topic about my mods that my car gets

Today i am gettin my first modification to my GTT im gettin a pod filter installed i shall show you what it looks like =]

*Laughing Out Loud* Nice one. . . . Pod filter = 50+ RWHP :wave:

You've caught Skyline aids!!!

But hey, don't worry about the people that knock you down, just keep the car as legal as possible, keep the penis extensions to the minimum, do it right, do it properly the first time! No one should be laughing at ya, Rome wasn't built in a day and neither are performance cars...

Bit by bit you will get the build you want dude! Patience, perserverence, good timing, good standards and balancing vision/ambition with pragmatism/realism is the best way to go!

Edited by Marco-R34GTT
yea ftmfw ahaha i no its not much but hey wat else can i do on a student wage :O

Haha my bad, u got to start from somewhere :) Then work ur way up! Soon ur going too want full exhaust system, FMIC, Cams, ECU, ect. . Then u will be like y am I always low on money?? :)

i already have the full exhaust system i think the next thing to do is get the FMIC and ECU and leave it at that i think? i like doing mods to the look of the car more then the performance, it can already go the speed limit

Unless your coilpacks are fkd there's no need to change them.

Hell, I'm running my stock 19yo coils and they're fine.

That’s Fair enough, u have had a good run. I just noticed with 3 of my R34 GT-T friends all are coils went around the 100 - 130k mark, I guess it was just bad luck. So when we went too change sparks (with 0.8 gap), we changed the coils while we were there. Just something too be aware off. Not everyone is lucky and sexy like bubba.

i already have the full exhaust system i think the next thing to do is get the FMIC and ECU and leave it at that i think? i like doing mods to the look of the car more then the performance, it can already go the speed limit

haha.. yeah we all plan to "leave it at that" ... 7 grand later...

it's addictive... suspensions mods will come soon. :D




  • Similar Content

  • Latest Posts

    • Yes. It's not aesthetically pleasing. And most turbos sold these days are sold for aesthetic purposes (Insta likes/fame, etc). Also its cheaper to not machine it. The hot side is the pipe with hot air in it from the turbo to the intercooler. The cold side is the pipe with cooled air in it from the IC to the engine. Anywhere after the turbo will do. Certainly before the IC is better than the IC. But there is no massive imperative to get it from the turbo scroll itself, or from no more than an inch downstream. Those are nonsense thoughts. The only thing we want is a pretty honest measurement of the pressure at the turbo outlet, and anywhere from the compressor housing itself to the inlet of the IC will read approximately the same thing. Yeah, I disagree with Tao on that one. It's fine for an engine that only runs on the dyno at full throttle (or, equivalently, a drag car that only really runs at full throttle also). But some turbos that are particularly sensitive to overspeed (ie EFRs) would quite possibly get into a lot of trouble if run that way.
    • The sarcasm should have been easily visible. It was dripping off it.
    • Whether the brakes will clear the back of the spokes comes down to the specific wheel, as well as its dimensions (ie 18x8 or whatever else size). You can have 2 different wheels of the same size and one will clear and on the other the spoke design will not clear. So your question "Anyone riding around with 18 inch. that can confirm "that it'll fit"?" cannot be answered in a meaningful way. You need that person to be using the same wheel you want to use.
    • I didn't even bother watching the video.
×
×
  • Create New...