Jump to content
SAU Community

Recommended Posts

Hi all, got the stock plumback BOV and everythin on my series 2 r33...has the standard rb25det...jus so that people know what they are dealin with....

i want the flutter noise thru my pod/airbox/air intake...whatever u want to call the setup.....

all i have is mass suction and then a massive whoooosh sound......but i want the flutter sound to come out instead...as it sounds better and all...but im not sure on which pipe i need to block or what exactly i need to do to the stock bov and piping to achieve this....

so can someone plz tell/show me....pictures would be greatly appriciated for this.....

need any more info jus ask...hope someone can help me out....

i have read that this will cause the car to stall....true/false???

Cheers

Matt

n.b. : i dont need the lecture that flutter is good or flutter is bad....i have looked into it and i know the consequences etc.....

Link to comment
https://www.sau.com.au/forums/topic/257935-flutter/
Share on other sites

easiest way to do it is get piece of 2mm alloy sheet and take the blow off valve off where it mounts to the cross over pipe and place the pipe on the sheet and trace it out and cut it out and drill the 2 screw holes in it and place that in there instead of the gasket. That way it still looks like a gasket but the air cant get to the blow of valve and gives u the flutter sound.

Link to comment
https://www.sau.com.au/forums/topic/257935-flutter/#findComment-4437248
Share on other sites

thts the dumbest thing that u could do as it will f**k up ur car the way that it makes the flutter sound is by instead of releasing the air thro the blow-off it sends it back into the turbo and that will make ur car run lean u'll get shit fuel consumption and constant staling.

if u want the noise then get a screamer pipe any of the tuning shops will be able to do it its a lot better then blocking of ur blow-off.

Link to comment
https://www.sau.com.au/forums/topic/257935-flutter/#findComment-4437311
Share on other sites

ive got a turbosmart mega sonic BOV and apexi super intake pod filter on my r33

i get the flutter and a stadard bov cshhh sound. changes depending on the boost it hitting. but with my flutter, i have free reved the car while watching the piston in the bov and see the piston bouncing to make the flutter. tried putting a plate where the bov is and it sounded shit.

so id say get a aftermarket bov and a pod filter. unsure of other ways but mine has done 0 damage.

i had the stalling problems but cleaned my AAC valve (DIY section) and increased the idle to around 800rpm and have no problems with stalling anymore.

Link to comment
https://www.sau.com.au/forums/topic/257935-flutter/#findComment-4437351
Share on other sites

thts the dumbest thing that u could do as it will f**k up ur car the way that it makes the flutter sound is by instead of releasing the air thro the blow-off it sends it back into the turbo and that will make ur car run lean u'll get shit fuel consumption and constant staling.

if u want the noise then get a screamer pipe any of the tuning shops will be able to do it its a lot better then blocking of ur blow-off.

No offence, but your an idiot and have no idea what your talking about.

It won't make the car run lean, it actually richens up the fuel mixtures with a blocked off valve on the stock ecu, so will run rich for that split second.

What the hell does a BOV and screamer pipe have to do with one another? They are completely different things. Do you even know what a screamer pipe is?

Mate do a search on "flutter", its been covered a million times.

Thread lock?

Edited by PM-R33
Link to comment
https://www.sau.com.au/forums/topic/257935-flutter/#findComment-4437436
Share on other sites

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...