Jump to content
SAU Community

Recommended Posts

hi all im selling my 180sx and upgrading to a stagea (wc34) and was just after some tips on what to look for and other traps when looking for a decent stagea (ive already read the stickyd buyers guide) also what type of fuel consumption are people getting?? all input is appreciated

Link to comment
https://www.sau.com.au/forums/topic/258089-buyina-a-stagea-help/
Share on other sites

make a list and i will answer :D

i am probably selling up this year for a 180 or s14, want something little and fun again before i need a family car haha

buying- drive MANY, consider what mods will be done asap, and use this to get the price down... mine needed shocks and tyres for RWC, so i got it cheaper and put bilteins and RE001's on.

check for rust around the mirrors and tailgate

check for broken cup holders :P

dont buy one with a cut battery tray-illegal

i have a shiftkit, full exhuast with highflow cat(under 90db :P )and a FMIC, i am down to a 1/4 tank right now and done 430km

the exhaust is the best thing for economy besides an SAFC or ECU

if not upping the boost, just get an R34 SMIC instead of an FMIC, more responsive :)

sunrooves are fkn PIMP... take it to a hand car wash and go nuts, check for leaks

either find one dead stock that has been a daily or family car, that is well maintained, or get one with QUALITY modifications

doesnt matter what the KM's are, the timing kit MUST of been done

series 1 with a DAYZ kit is the best looking IMO, the kit is ~1500AUD+ to purchase second hand, easier to find one with one

will add more later

argeed with last post...

rust on top of strut towers, nere fuel tank sumtimes.

remember its a 10+ yr old car so theres going to be 'beat down'points

shipping from interstate will cost you around the 600$ mark

and changing fron state to state will requier some form of check.

remember if its too good to be true it probly is. listen for noises in the engin that may be weird,

if theres a cut in the battery seat, or the fan is slightly trimmed its been FMIC, check the bolt that holds the boost solinoid down

coil packs are exensive and will need to be done when they go... if the car jolts under boost its probly them

being boosted is ptobly the only drama... if the hoses look liek there all in the proper spots u should b fine

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

how do the n/a stageas gor or should i just get a turbs one

could you add on that a bit please mate

he means the timing belt, idler bearing and water pump must be changed. nissan reccomends it to be done at 100 000km, but it is good practice and also gives you piece of mind that it be done.

Edited by QWK32
how do the n/a stageas gor or should i just get a turbs one

N/A models are not eligible for SEVS/RAWS (whatever it is these days) importing.

The models you'll fine in Australia are (I think!):

WGNC34:

S1 - RSF, RSFV (+ DAYZ), 260RS

S2 - RSV, RSFV (+ DAYZ), RSFS, 260RS

NM35 (S1 only, at this stage...):

250tRSFV (+ DAYZ), 250t RXF, 250tRSFV HICAS, AR-X, Autech

There were also 'aero' models of most of the above. From what I've seen around, the most common ones are ;S1 RSFV/260RS, S2 RSFV/260RS/RSFS, NM35 250tRSFV, AR-X.

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

i get 9-12L/100km atm, lead footed suburb driving and fwy driving, not fwy cruising :laugh: 450-550km per tank

avoid one that has been boosted, but look for the mods you want done already... LIKE MINE :thumbsup:

i get 9-12L/100km atm, lead footed suburb driving and fwy driving, not fwy cruising :laugh: 450-550km per tank

avoid one that has been boosted, but look for the mods you want done already... LIKE MINE :thumbsup:

9-12 sounds sweet thats heaps better than what people have benen telling me

Get a racv check for peace of mind also.

Try and find one that looks like no one has moded/cut anything anywhere, whether that be interior or under the hood.

Llike any car, try to find one thats clean no signs of rust, dints, hacked interior from shit stereo installs, the usual:

-footwells - check for damp carpet (could be evidence of leaking from heater core or water coming in around firewall.

-spare tyre area under carpet - check for water/dampness

-no smokey exhaust.

-no roughness/shunting from the gearbox/auto when accelerating.

-rust under mirrors & around tailgate lights. (already been said)

Personally I was lucky, found one that did in fact appear to owned by '1 lady owner',

it is that clean/neat/mechanically perfect, looks like it had only been a few months out

of the showroom and drives like one....for a 10yr old car!

I keep getting asked 'when did Nissan release this, is it new?'.....There jaws drop when i say its a 98 model.

p.s. in my opinion your better to get one that has not been moded, start fresh with you own mods and you know what has/hasnt been done. Also you'll find a car thats been moded has tended to have had a hard life.

Edited by Stagea_Neo
Get a racv check for peace of mind also.

Try and find one that looks like no one has moded/cut anything anywhere, whether that be interior or under the hood.

Llike any car, try to find one thats clean no signs of rust, dints, hacked interior from shit stereo installs, the usual:

-footwells - check for damp carpet (could be evidence of leaking from heater core or water coming in around firewall.

-spare tyre area under carpet - check for water/dampness

-no smokey exhaust.

-no roughness/shunting from the gearbox/auto when accelerating.

-rust under mirrors & around tailgate lights. (already been said)

Personally I was lucky, found one that did in fact appear to owned by '1 lady owner',

it is that clean/neat/mechanically perfect, looks like it had only been a few months out

of the showroom and drives like one....for a 10yr old car!

I keep getting asked 'when did Nissan release this, is it new?'.....There jaws drop when i say its a 98 model.

p.s. in my opinion your better to get one that has not been moded, start fresh with you own mods and you know what has/hasnt been done. Also you'll find a car thats been moded has tended to have had a hard life.

I've got one for sale right now. 122,000 kms. New waterpump and timing belt. Stock as, except for pod filter and 18" ROH mags.

I was tempted to mod mine to make it more 'attractive' to buy, but went with keeping it stock as blank canvass for the buyer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...