Jump to content
SAU Community

Recommended Posts

hi all im selling my 180sx and upgrading to a stagea (wc34) and was just after some tips on what to look for and other traps when looking for a decent stagea (ive already read the stickyd buyers guide) also what type of fuel consumption are people getting?? all input is appreciated

Link to comment
https://www.sau.com.au/forums/topic/258089-buyina-a-stagea-help/
Share on other sites

make a list and i will answer :D

i am probably selling up this year for a 180 or s14, want something little and fun again before i need a family car haha

buying- drive MANY, consider what mods will be done asap, and use this to get the price down... mine needed shocks and tyres for RWC, so i got it cheaper and put bilteins and RE001's on.

check for rust around the mirrors and tailgate

check for broken cup holders :P

dont buy one with a cut battery tray-illegal

i have a shiftkit, full exhuast with highflow cat(under 90db :P )and a FMIC, i am down to a 1/4 tank right now and done 430km

the exhaust is the best thing for economy besides an SAFC or ECU

if not upping the boost, just get an R34 SMIC instead of an FMIC, more responsive :)

sunrooves are fkn PIMP... take it to a hand car wash and go nuts, check for leaks

either find one dead stock that has been a daily or family car, that is well maintained, or get one with QUALITY modifications

doesnt matter what the KM's are, the timing kit MUST of been done

series 1 with a DAYZ kit is the best looking IMO, the kit is ~1500AUD+ to purchase second hand, easier to find one with one

will add more later

argeed with last post...

rust on top of strut towers, nere fuel tank sumtimes.

remember its a 10+ yr old car so theres going to be 'beat down'points

shipping from interstate will cost you around the 600$ mark

and changing fron state to state will requier some form of check.

remember if its too good to be true it probly is. listen for noises in the engin that may be weird,

if theres a cut in the battery seat, or the fan is slightly trimmed its been FMIC, check the bolt that holds the boost solinoid down

coil packs are exensive and will need to be done when they go... if the car jolts under boost its probly them

being boosted is ptobly the only drama... if the hoses look liek there all in the proper spots u should b fine

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

how do the n/a stageas gor or should i just get a turbs one

could you add on that a bit please mate

he means the timing belt, idler bearing and water pump must be changed. nissan reccomends it to be done at 100 000km, but it is good practice and also gives you piece of mind that it be done.

Edited by QWK32
how do the n/a stageas gor or should i just get a turbs one

N/A models are not eligible for SEVS/RAWS (whatever it is these days) importing.

The models you'll fine in Australia are (I think!):

WGNC34:

S1 - RSF, RSFV (+ DAYZ), 260RS

S2 - RSV, RSFV (+ DAYZ), RSFS, 260RS

NM35 (S1 only, at this stage...):

250tRSFV (+ DAYZ), 250t RXF, 250tRSFV HICAS, AR-X, Autech

There were also 'aero' models of most of the above. From what I've seen around, the most common ones are ;S1 RSFV/260RS, S2 RSFV/260RS/RSFS, NM35 250tRSFV, AR-X.

Rust under the door mirrors is the most common fault. I have had two Stageas and got both of them professionally welded/painted.

I would be looking for one that already has the Bilsteins, sway bars, fmic if you want that already done, and a manual if that is your goal. If it's not blowing smoke and doesn't rattle these things are good for at least 300,000km.

p.s.I am glad you said fuel consumption and not fuel economy - these will go like a 6L V8 and use petrol accordingly.

p.p.s I have just bought my third Stagea (the first was n/a, the 2nd written off - my fault, not the car).

i get 9-12L/100km atm, lead footed suburb driving and fwy driving, not fwy cruising :laugh: 450-550km per tank

avoid one that has been boosted, but look for the mods you want done already... LIKE MINE :thumbsup:

i get 9-12L/100km atm, lead footed suburb driving and fwy driving, not fwy cruising :laugh: 450-550km per tank

avoid one that has been boosted, but look for the mods you want done already... LIKE MINE :thumbsup:

9-12 sounds sweet thats heaps better than what people have benen telling me

Get a racv check for peace of mind also.

Try and find one that looks like no one has moded/cut anything anywhere, whether that be interior or under the hood.

Llike any car, try to find one thats clean no signs of rust, dints, hacked interior from shit stereo installs, the usual:

-footwells - check for damp carpet (could be evidence of leaking from heater core or water coming in around firewall.

-spare tyre area under carpet - check for water/dampness

-no smokey exhaust.

-no roughness/shunting from the gearbox/auto when accelerating.

-rust under mirrors & around tailgate lights. (already been said)

Personally I was lucky, found one that did in fact appear to owned by '1 lady owner',

it is that clean/neat/mechanically perfect, looks like it had only been a few months out

of the showroom and drives like one....for a 10yr old car!

I keep getting asked 'when did Nissan release this, is it new?'.....There jaws drop when i say its a 98 model.

p.s. in my opinion your better to get one that has not been moded, start fresh with you own mods and you know what has/hasnt been done. Also you'll find a car thats been moded has tended to have had a hard life.

Edited by Stagea_Neo
Get a racv check for peace of mind also.

Try and find one that looks like no one has moded/cut anything anywhere, whether that be interior or under the hood.

Llike any car, try to find one thats clean no signs of rust, dints, hacked interior from shit stereo installs, the usual:

-footwells - check for damp carpet (could be evidence of leaking from heater core or water coming in around firewall.

-spare tyre area under carpet - check for water/dampness

-no smokey exhaust.

-no roughness/shunting from the gearbox/auto when accelerating.

-rust under mirrors & around tailgate lights. (already been said)

Personally I was lucky, found one that did in fact appear to owned by '1 lady owner',

it is that clean/neat/mechanically perfect, looks like it had only been a few months out

of the showroom and drives like one....for a 10yr old car!

I keep getting asked 'when did Nissan release this, is it new?'.....There jaws drop when i say its a 98 model.

p.s. in my opinion your better to get one that has not been moded, start fresh with you own mods and you know what has/hasnt been done. Also you'll find a car thats been moded has tended to have had a hard life.

I've got one for sale right now. 122,000 kms. New waterpump and timing belt. Stock as, except for pod filter and 18" ROH mags.

I was tempted to mod mine to make it more 'attractive' to buy, but went with keeping it stock as blank canvass for the buyer.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...