Jump to content
SAU Community

Boost Problem

jarrodgtr

By jarrodgtr,
in Engines & Forced Induction

 Share

Recommended Posts

jarrodgtr Rookie

jarrodgtr

Posted
Posted

Hi

I recently bought my 32 GTR and couldn't get it over .5bar

So i cut out the restrictors in the hoses

Then found it had a narrower cat so got a 3in hi flow cat

and ran it with no exhaust to rule out blockage in exhaust

Cleaned the intercooler out and piping

Have cleaned out the bovs

I ran a hose from the waste gate straight to the manifold

Then just changed the turbos with another set of standard GTR turbos and still have the same problem

Was wondering if anyone has had same problem? Has anymore ideas? Or what could be happening?

Im out of ideas

Cheers Jarrod

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/
Share on other sites
jarrodgtr Rookie

jarrodgtr

Posted
  • Author
Posted
have you got any boost control? you cant just run a line straight from the waste gate to the manifold cause you will only run waste gate pressure.

Just the stock boost controller that is to the left of the engine bay when you look from front on. Have also tried a GFB Atomic Boost controller. Have also disconnected the lines to the wastegates which "should have" boosted to 1.8bar and blown turbos...... but no.. still runs at 0.5bar

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/#findComment-4441607
Share on other sites
jarrodgtr Rookie

jarrodgtr

Posted
  • Author
Posted
How are the actuators on the turbos ? checked those ?

They are fine, the second set of turbos came with actuators as well and still the same problem...

both the turbos and actuators have been changed....

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/#findComment-4441628
Share on other sites
jarrodgtr Rookie

jarrodgtr

Posted
  • Author
Posted

The cam belt has been changed and my flatmate is suggesting that who ever changed the belt may have put it on the wrong tooth on the exhaust cam.... which could lead to the exhaust valves closing too early....

Thats all he could think of, what do you guys think?

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/#findComment-4441675
Share on other sites
Pal Veteran

Pal

Posted
Posted

they would have to close late to bleed of the boost, think you are going to need to get it onto a dyno, watch the wate gate actuators to see when they are opening, see how boost is being made and check timing. its a strange one!

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/#findComment-4441707
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

if base timing is wrong the engine will be sluggish, poor performance and probably wont make much boost

check with a timing light, should be 15deg base timing at idle, if the belt was fitted wrong, this would be a likely explanation

Link to comment
https://www.sau.com.au/forums/topic/258177-boost-problem/#findComment-4441718
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...