Jump to content
SAU Community

Recommended Posts

Hey guys/girls,

Recently Sold my Skyline... All Left over parts I'm selling for cheap as i don't care anymore.

Prices are firm but if you think they prices are unfair, feel free to shoot me a PM and we'll discuss prices.

All parts Located in Melbourne Western suburbs - Pick up only. Will Post interstate at buyers expense.

Contact me via PM or text/call me directly on: 0421 205 751

2x Front TANABE SUSTEC DAMPER Shocks and RSR Lowered Springs for R32.

These Shocks are in excellent condition and are Damper adjustable. Only have the front 2 sorry. - $250

2x Front OEM R33 Shocks

In good condition, no leaks or rust - $200

R33 S2 dash surround

Perfect condition no cracks or broken vents. - $60

R33 GTSt OEM BOV

perfect condition - $30

R33 GTR OEM BOV

Gread upgrade for GTST's.. works fine - $70

R32/33 GTR OEM adjustable strut brace

good condition - $100

R33 S2 GTST drive and passenger seats

Both seats comes with rails. Passenger seat has no damage. Driver has small rip. (see pic) - $120 for the pair

R33 S2 Spoiler

White, No damages. LED tail lights works fine - $60

R33 Right had side tail light.

No cracks on plastic. Needs clean. Comes with working globes - $60

R33 Stock actuator

Works fine - $30

R33 S2 Manual Turbo ECU

Works fine - $50

R33 Dual pillar pods - suits 60mm gauges

Sits flush, goes form roof to dash - $50

R33 Stock Turbo

Comes with actuator and elbow - has around 1-2mm shaft play in and out. other wise, works fine. - $250

6x 480cc side feed injectors for RB25DET (not NEO)

Bench flowed, tested and cleaned - $500

R33 Clutch master cylinder

works 100% comes with original lines. Slave cylinder not included. - $50

p3090727.jpg

p3090728.jpg

p3090721.jpg

p3090722.jpg

p3090723.jpg

p3090724.jpg

p3090725.jpg

p3090726.jpg

p3090729.jpg

p3090730.jpg

p3090731.jpg

p3090732.jpg

p3090733.jpg

p3090734.jpg

p3090735.jpg

Edited by Dush
Link to comment
https://www.sau.com.au/forums/topic/260308-skyline-parts-clean-out-melb/
Share on other sites

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

looking at the sustec damper shocks, how much for shipping to NSW 2640?

and they will fit R32 gtst? and how low are the springs? im running on 18's and they just fit under the well on the stock shockers

Thanks mate

Just an update of the Parts that are still available:

2x Front TANABE SUSTEC DAMPER Shocks and RSR Lowered Springs for R32.

These Shocks are in excellent condition and are Damper adjustable. Only have the front 2 sorry. - $250

2x Front OEM R33 Shocks

In good condition, no leaks or rust - $200

R33 S2 dash surround

Perfect condition no cracks or broken vents. - $60

R33 GTSt OEM BOV

perfect condition - $30

R33 GTR OEM BOV - SOLD

R32/33 GTR OEM adjustable strut brace

good condition - $100

R33 S2 GTST drive and passenger seats

Both seats comes with rails. Passenger seat has no damage. Driver has small rip. (see pic) - $120 for the pair

R33 S2 Spoiler

White, No damages. LED tail lights works fine - $60

R33 Right had side tail light.

No cracks on plastic. Needs clean. Comes with working globes - $60

R33 Stock actuator

Works fine - $30

R33 S2 Manual Turbo ECU - SOLD

R33 Dual pillar pods - suits 60mm gauges

Sits flush, goes form roof to dash - $50

R33 Stock Turbo

Comes with actuator and elbow - has around 1-2mm shaft play in and out. other wise, works fine. - $250

6x 480cc side feed injectors for RB25DET (not NEO)

Bench flowed, tested and cleaned - $500

R33 Clutch master cylinder

works 100% comes with original lines. Slave cylinder not included. - $50

Everything has to go.. so inquire within. =]

hey mate

have you still got the spoiler??

thanks

The Spoiler and Dash surround maybe sold. Just waiting for the guy to pick it up... If it falls threw. I will post it back up on this thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...