Jump to content
SAU Community

Brembo Brakes

roadandrace
 Share

Recommended Posts

roadandrace Collaborator

roadandrace

Posted
Posted

I am upgrading my brakes and will have a full set of R33 GTR brembo brakes and rotors for sale sometime next week. They are in good condition with plenty of life left on the rotors.

Price is $1800 which seems to be the going rate.

I may consider trading a set of standard Nissan GTR calipers and rotors, which I need for another project vehicle.

Drop me an email if interested and I will respond ASAP.

Link to comment
https://www.sau.com.au/forums/topic/260360-brembo-brakes/
Share on other sites
roadandrace Collaborator

roadandrace

Posted
  • Author
Posted
I am upgrading my brakes and will have a full set of R33 GTR brembo brakes and rotors for sale sometime next week. They are in good condition with plenty of life left on the rotors.

Price is $1800 which seems to be the going rate.

I may consider trading a set of standard Nissan GTR calipers and rotors, which I need for another project vehicle.

Drop me an email if interested and I will respond ASAP.

Brembo's are located in western Sydney.

Link to comment
https://www.sau.com.au/forums/topic/260360-brembo-brakes/#findComment-4467722
Share on other sites
roadandrace Collaborator

roadandrace

Posted
  • Author
Posted
Replied to PW's today so check your messages and get back to me.

Regards

It looks like taking a trade is going to be too hard so anybody interested in buying the brembo calipers and rotors outright is welcome to make a realistic offer.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/260360-brembo-brakes/#findComment-4472147
Share on other sites
roadandrace Collaborator

roadandrace

Posted
  • Author
Posted
Hi there, do you have any pictures? Will they require a rebuild or refurbish, etc, etc?

Were working fine and should be okay to run as is. Brembo's have a very simple piston seal setup and wouldn't be prone to damage unless you run them without dust boots, use crap brake fluid or don't change the fluid as recommended. The workshop manual says the seals and boots should be changed every five years for standard GTR calipers so I would think that Brembo's are similar. Obviously they don't last forever and will require maintenance at some point. I can't verify what life they have had before I purchased them, but I can say that I only drive my car every 3 to 4 weeks and not daily. They do show their age as the brembo stickers are dull and some of the paint is chipped so they would need a paint and new stickers if you're looking for show quality. The rotors are standard (not drilled or slotted) and have heaps of material left on them. I hope this helps and I will try to add some pic's tomorrow.

Link to comment
https://www.sau.com.au/forums/topic/260360-brembo-brakes/#findComment-4476687
Share on other sites
Line 3 Community Regular

Line 3

Posted
Posted

you wouldnt be interested in a set of z32 brakes (calipers and rotors) by any chance ?

i'm pretty sure there the same as the standard r33 brake setup...let me know as i will be looking for a brake upgrade soon.

Link to comment
https://www.sau.com.au/forums/topic/260360-brembo-brakes/#findComment-4483432
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...