Jump to content
SAU Community

Recommended Posts

Hey guys,

I got my stock plenum polished up and when I put it back on again ( new gaskets ) I got this hissing noise coming from around the plenum when the throttle is open up.

Its definetely not a vacuum leak because the car is idling perfectly normal and its boosting fine

Any help would be greatly appreciated :P

Thanks

It can still be a vacuum leak, just a small one. You can try pressure test your intake manifold by blocking the pipe where it comes from the turbo's and then pumping up the intake manifold. If there is a leak it wlll be audiable at 2-3psi.

If everything is good you should be able to pump it up to 15psi and it should hold that pressure. Just be sure your plug doesnt blow out of the intake plumbing or it could launch quite a distance and cause some damage or injury.

what about the auxilary air control? was that taken off when polished? not sure how 34's go... but in 33's it is at the back of plenum (towards the firewall) and it lets in a small amount of air when idle (so the car doesnt stall when the throttle is closed) via a screw.... maybe you can just hear that because its clean now? or whats the condition of the gasket of it?

Its kinda hard to explain the problem so I will describe it the best I can

The hissing noise just appears when the throttles just open up , so if I hold the throttles open in any rpm it will NOT make the hissing noise

It sounds like "pssst" then goes away after that

The car is idling fine and boosting fine.

naut : The car is an R34 GTR its only running the factory boost sensor on the screen , you reckon I should check the vacuum hose ?

WYTSKY : I did taken out the AAC valve and put it back on with NEW gasket and I did NOT fiddle with the screw that controls the idle

Any more ideas / input ?? Im confused now :banana:

Thanks boys

By having the noise go away when you open the throttles it is confirming that it is a vacuum side leak. Meaning the leak is between the throttles and the cylinder head.

3 possabilities...

1. The gasket you relaced under the AAC valve.

2. Throttle shaft seals

3. throttle gaskets

Pressure test it and it will tell you which one it is.

VSPEC R33 : I have replaced all the six individual throttle gaskets , I did MAKE my own gasket for the AAC from gasket paper I have lying around

and which one is the Throttle Shaft seals ?

Thanks

Okay so I took the car to 2 garages and all of them sprayed brake kleen on the plenum + AAC and they couldnt seem to find any leak at all

ALTHOUGH the car is idling higher than before , its just above 1k rpm on idle

Anymore thoughts guys ??

Pressure test. Trust me you wont regret it. Youd be amased at how you can find the smallest leaks so easily, and as a reward your boost response will be better than you ever thought possible when its fixed.

tulalit where are you located mate???

QLD????

If so we have a span on gas machine that we can check of air leak's, vacuum leak's and boost, takes two Min's to hook up, or go to a shop that has one in your area.

Hey guys thanks for the replies :D

EFI Performance : I live in New Zealand , so I will take the car to ST Hitec on friday and see what he says ;)

Meanwhile I will replace the AAC gasket again see if it changes anything :)

Any feedbacks will be much appreciated :)

Since some of you mentioned the PCV valve, it occurred to me to mention the one way valve that is on the clutch vacuum booster. Ive seen them fail and then once the diaphram fails in the clutch booster it will actuall suck air from the clutch booster leak which will increase the idle speed.

Usually you can hear the leak inside the car if you just operate the clutch pedal when the car is idling. Its pitch will change as the diaphram moves.

Well I took the car to ST Hitec and he said I shouldnt worry about it and just leave it and he couldnt find any leak whatsoever

I might rip the plenum off one more time to replace it with metal gaskets this time

Thanks boys :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...