Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

lol hor hor horrrr

bitches we all going to the baskins meet?

also are they building 2 speed cameras along the centenary freeway between mt cootha exit and indooroopilly exit? fuuufffuuuuu

Serious?

That run is so easy to sit on 180kph limiter :)

ooh service!!!

hate CA heater pipes!! fffuuuu

use lube and it doesnt hurt as much ;)

ps tasman ill give you a bell tonighttt - you at work late?

Hey guys,

I put my car on carsales thinking it'd sit on there for a while, and by the time I actually wanted to sell it, it might be getting some interest. turns out it was on there for 5 days and i sold it for more than i bought it for, couldn't turn down the offer, so there we go, no more gtr !

Maybe i'll come to one of those meets in another one some time, gonna have a look at a couple this weekend, not sure what to get though, anyway take it easy.

J

Hey guys,

I put my car on carsales thinking it'd sit on there for a while, and by the time I actually wanted to sell it, it might be getting some interest. turns out it was on there for 5 days and i sold it for more than i bought it for, couldn't turn down the offer, so there we go, no more gtr !

Maybe i'll come to one of those meets in another one some time, gonna have a look at a couple this weekend, not sure what to get though, anyway take it easy.

J

no shit!

i have heard that from other ppl - they waste their time on forums, then wack it on car sales and it sells in a week

but dont lie to us - u are never coming to a baskins meet :P

Edited by astrotristan2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...