Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

It’s around a 15% driveline loss.

So say 255awkw + 15% loss (38kw) = 293rwkw = 392rwhp

Which is about right for a standard N1.

@super coach tristan: tried a new grip tonight and got 51 with a strike rate of ~210 :blink:

Also got about 2 dozen stumpings and catches behind the stumps and a few wickets bowling. Good night (y)

To break it down more, rwkw to flywheel kw is roughly x1.33

so, 293rwkw x 1.33 = 389FLYWHEEL KW

Both post's above are rough, everyone has different veiws on loss and conversion rates

Maybe all these while the 300kw I had in mind was rw not aw. But the fact that the car feels lighter/smoother really surprises me. 1st gear used to hit limiter at 60-70km/h now it goes up to 80+. Amazed.

A stock N1 will never make 300awkw, unless the dyno is happy, or you tell the tuner to input 300awkw on the graph lol.

Your car is very healthy and is on par - What else is done to it?

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

Wooooo good shit

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Glad to hear the tune is good Brandon, who tuned it for you?

They must have lifted the rev limit a bit :blink:

Gavin Woods @ Autotech. Shit loads of GTRs... oh and 1 Tommy Kaira 32 (dont know real or not)

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

He reckon its restriction. Or maybe injectors (he's not comfortable running higher than 90%). Or might be the boost controller (I've heard the kit doest hold boost very well after 20psi)

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Don’t get me wrong, Gavin knows more about Nissans than most people – however to cut a VERY long story short, I bought a second hand Q45 throttle body from a wrecker, unknown to me at the time the wrecker swapped the TPS unit for a ca18 unit, which meant the car wasn’t tunable… My car was with Gavin for a full day and he couldn’t find what was wrong with it.

I took it to Matty and he found within 5 minutes that the TPS had been swapped over, we put the correct Q45 TPS in and had it tuned…

I know where I will continue to keep going back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I think he was only proposing to use the wire, not the sender. Simply because it runs from the right place to the right place. Personally, I wouldn't hack up the factory wiring like that. I'd just lay in the Defi loom.
    • From memory it wasn't too hard to simply see which wire ran where when you plug that in. Unfortunately also from memory the OEM sender does not use the same configuration 99.9% of gauges run. So in other words if you connect the signal wire that was running to the OEM gauge to your DEFI gauge you might find your oil reads at 200C or some other incorrect value. I remember having the same line of thought and then running new wires/senders to match the gauges I have. The pinout is available in the R34 workshop manual.
    • Does anyone on here know which wire on the GTT triple gauge pod harness is for the oil temp gauge? my sensor works fine but I upgraded the gauges to DEFI advance. And if I can simply piggyback off the oem oil temp wire to the Defi oil temp sensor wire that would make life so much easier. 
    • Even face her a wash now that’s it worth more than my house
    • This was what I was invisioning, or Pete cutting a beer can up and hose clamping it around the catch can! Ha ha ha
×
×
  • Create New...