Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

umm looks pretty scary outside, ive covered her all up. hope the plastic dont leak :down:

saw a couple of holes in your covers :P , hope it does hold off. Underside looks real nice. Awesome job boys.

Shan turns out the D-max aus is fake and no one should buy it!

its actually racespec thats using a D-max business card and sources parts actually not from D-max but cheap shit like DMD

shan i sent you a email with .zip fileE!!!!! answer me bish!!! i need it done mate to get your overfenders mate!!!

oh and about the front bar for the R32??

found my so called setup for the time being!

2003635688296282382_rs.jpg

2003695429584753463_rs.jpg

looks like im getting d-max overfenders too black man! edit: shan :P

anyone who wants D-max gear should contact me directly!

Edited by Redsuns88
that lip is f**king epic.

how'd the 180 go?

taR

180 was good - just the turbo proved painful - we were setting it up but then realised that we didnt have an adapter for the oil lines, so shes not going to be ready until next weekk

and yeh - that lip kit is amazing, hint hint

so 1 more week of RB goodness eh tristan. I can't see any of those pics cus work comp is being gay :banana:

Greasy roads on the way to work this morning were good fun :domokun:

lol tas, that car is sporting mad Do-Luck front sides n rear... I'm not using the front cos I prefer my front bar to it, lot more aggro. but yeah uleh, hook me up with dmax's i'll have a look at your stuff tonight.

I threw up on my keyboard and I blame you..Now I'll have to eat breakfast all over again...

+1 :domokun:

just grab a spoon and eat it off the keyboard.

I solve problems.

Thanks . . . that actually works

finally got the underneath fully seem sealed and 2k primed this morning. tomorrow i will sand it back lighty and spray the black (plz not look like nissan stnd black :domokun: ) lol, then ill put some deadner in the arches and through the tunnel.

P9050001.jpg

mmm white goodness, and a sneak preview of how stealth the welded bolt on mounts look (i started off neat seem sealing then started to seal like josh and his sunroof) but still looks the part. no rust for DAVE

yay

P9050004.jpg

peace out.

that's not stealth, that looks like you cut a bit of your floor out and welded in a plate. then took an enema and around where it was welded you had a fluid, bubbly stream of shit to line it. then you painted over it to cover it up.

that's not stealth, that looks like you cut a bit of your floor out and welded in a plate. then took an enema and around where it was welded you had a fluid, bubbly stream of shit to line it. then you painted over it to cover it up.

you were close but no cigar. there is a plate either side welded to the floor plan. and as i said i seem sealed it josh stylez.

can you tell now.

P9050001-1.jpg

glad i did the underside, got a few runs, needa tweek my gun abit. its good that its underneath but still it could be better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...