Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

umm looks pretty scary outside, ive covered her all up. hope the plastic dont leak :down:

saw a couple of holes in your covers :P , hope it does hold off. Underside looks real nice. Awesome job boys.

Shan turns out the D-max aus is fake and no one should buy it!

its actually racespec thats using a D-max business card and sources parts actually not from D-max but cheap shit like DMD

shan i sent you a email with .zip fileE!!!!! answer me bish!!! i need it done mate to get your overfenders mate!!!

oh and about the front bar for the R32??

found my so called setup for the time being!

2003635688296282382_rs.jpg

2003695429584753463_rs.jpg

looks like im getting d-max overfenders too black man! edit: shan :P

anyone who wants D-max gear should contact me directly!

Edited by Redsuns88
that lip is f**king epic.

how'd the 180 go?

taR

180 was good - just the turbo proved painful - we were setting it up but then realised that we didnt have an adapter for the oil lines, so shes not going to be ready until next weekk

and yeh - that lip kit is amazing, hint hint

so 1 more week of RB goodness eh tristan. I can't see any of those pics cus work comp is being gay :banana:

Greasy roads on the way to work this morning were good fun :domokun:

lol tas, that car is sporting mad Do-Luck front sides n rear... I'm not using the front cos I prefer my front bar to it, lot more aggro. but yeah uleh, hook me up with dmax's i'll have a look at your stuff tonight.

I threw up on my keyboard and I blame you..Now I'll have to eat breakfast all over again...

+1 :domokun:

just grab a spoon and eat it off the keyboard.

I solve problems.

Thanks . . . that actually works

finally got the underneath fully seem sealed and 2k primed this morning. tomorrow i will sand it back lighty and spray the black (plz not look like nissan stnd black :domokun: ) lol, then ill put some deadner in the arches and through the tunnel.

P9050001.jpg

mmm white goodness, and a sneak preview of how stealth the welded bolt on mounts look (i started off neat seem sealing then started to seal like josh and his sunroof) but still looks the part. no rust for DAVE

yay

P9050004.jpg

peace out.

that's not stealth, that looks like you cut a bit of your floor out and welded in a plate. then took an enema and around where it was welded you had a fluid, bubbly stream of shit to line it. then you painted over it to cover it up.

that's not stealth, that looks like you cut a bit of your floor out and welded in a plate. then took an enema and around where it was welded you had a fluid, bubbly stream of shit to line it. then you painted over it to cover it up.

you were close but no cigar. there is a plate either side welded to the floor plan. and as i said i seem sealed it josh stylez.

can you tell now.

P9050001-1.jpg

glad i did the underside, got a few runs, needa tweek my gun abit. its good that its underneath but still it could be better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...