Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

+1 for not drinking cheap stuff.

except out on the town. decent stuff is just too exxy sometimes.

Yep that's true. That's why you get fully sauced before your go

or not go out much, i really dont drink alot anymore.

I use to drink a lot for the 6 months i had no license

I don't go out much don't feel like either getting bashed or glassed... Stupid people getting drunk and nasty. I don't know about you but when I get sauced I just get happy and sleepy and do stupid sh_t. Like this one time at band camp....

I use to drink a lot for the 6 months i had no license

yeh when my 32 was out of action i found i drank a lot more hahaha

cuz ppl drove me or i bused it (or bmxed it :thumbsup:), so i didnt need to worry about making sure i wasnt drinking when i needed to get places

yeh when my 32 was out of action i found i drank a lot more hahaha

cuz ppl drove me or i bused it (or bmxed it :thumbsup: ), so i didnt need to worry about making sure i wasnt drinking when i needed to get places

I found the same... what a fun month that was and it was extremely blury

Martin, pretty sure I saw you zooming around the indro bowls club earlier tonight. I was once again in the beast*

*1999 ford festiva, 1.3l, automatic

Was that you following me? I thought you were a D car or something :thumbsup:. I've gone all paranoid like Dan

Martin - I'm not dogging you guys. And I'm not putting hos before bros. Just can't be assed coming on here lately.

Poor form

I'm finishing off a bottle of bourbon by drinking from the bottle

Alcoholic. I thought you wern't drinking much any more? Oh wait:

i really dont drink alot anymore.

Contradiction much? Seek help, you god damn alco

Poor form

Yeah, that's pretty much why I haven't been on. There's too much poor form on here lately. I think some heads need to be removed from some asses. And while we're at it, some lips needs to be removed from some asses too.

More than likely see you all on Thursday anyway.

Morning whores!!!

Morning!

Yeah, that's pretty much why I haven't been on. There's too much poor form on here lately. I think some heads need to be removed from some asses. And while we're at it, some lips needs to be removed from some asses too.

More than likely see you all on Thursday anyway.

:thumbsup: Thats why you need to come back bro. You can lift the standard with some quality tractor/boat jokes!

Wait summer is here...

Mmmmm glad I have air con in my classic antique. Anyone not got working air con? Bet that tractor doesn't.

Mmmmm glad I have air con in my classic antique. Anyone not got working air con? Bet that tractor doesn't.

Poor form, poor form! Just too much poor form going on around here. Don't be so poor form and and pay out tractors!

yeh pay out my tractor, i enjoy it :)

and then with any luck beck will say something priceless and ill have a new sig :thumbsup::D

mind you my current one is pretty unbeatable

yeh pay out my tractor, i enjoy it :D

and then with any luck beck will say something priceless and ill have a new sig :thumbsup::)

mind you my current one is pretty unbeatable

Hey... lol

I'm being extra careful with what i say from now on.. lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...