Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

plol hahaha

so i just finished creating a dream list of parts..

all mainly Mines..

and then i saw.. the price of them rebuilding your engine..

about 23k + freight..

Edited by Redsuns88

23k for a 26?? Sure the mines car is responsive, but i know a better way to get response for that sort of money.....OS Giken RB30 :whistling:

Ive pretty much got my dream list, all i need is an assembled bottom end and decent brakes!

plol hahaha

so i just finished creating a dream list of parts..

all mainly Mines..

and then i saw.. the price of them rebuilding your engine..

about 23k + freight..

Depends on what you get for that 23k. If thats for a crate motor all ready to go incl ancillaries(spelling?) then its not too bad.

23k for a 26?? Sure the mines car is responsive, but i know a better way to get response for that sort of money.....OS Giken RB30 :whistling:

Ive pretty much got my dream list, all i need is an assembled bottom end and decent brakes!

Giken 30 you pay 23k just for the short block! Whats the specs on yours?

oh and newer suspension, its ok but it looks like its very old

Bilstein Kit from Dan is good :thumbsup:

plol hahaha

so i just finished creating a dream list of parts..

all mainly Mines..

and then i saw.. the price of them rebuilding your engine..

about 23k + freight..

Just reread that and saw that word lol. Again it depends on what you get in one of their rebuilds but 23k is f**king exxy.

its got the head too with cams of your choosing it was 26k last time i checked for that, but that was delivered.

General specs are

HKS 2510s that were slightly highflowed upon rebuilding so are rated at about 325hp each instead of 310

Ported Head

Tomei Poncams so whats that 260 somthing degrees and 10mm of lift? somthing like that anyway

Power FC (Want to change that to the new adaptronic super ECU)

Z32 AFMs

Sard 750cc injectors in a Sard fuel rail with a sard FPR and some big intank pump

Trust dumps and front pipes into some random 3.5 inch exhaust

ARC intercooler

Profec B spec 2

Apexi intake piping and pods

NPC Twinplate

Rebuilt Gearbox

Rebuilt 4wd system

Rebuilt drive shafts

19row oil cooler

Oil mods to the head, restrictors drain at the back of the head ect

Baffled sump

Currently being done

Rebuild including:

ACL pistons

Spool rods

and new billett oil pump gears designed by shrek and ranga

external fuel pump and surge tank

I think thats about it

Tis a very nice list :D

omg colin since when do you design stuff? :whistling:

:thumbsup: I don't. Not oil pump gears anyway. That be Shanef :D

i have literally deflated my left nut over this..

Ex_SuperOutlet_P2_1000.jpg

and my right one

Ex_FrPipe_PTi_1000.jpg

tomei?

FK this, I wanted to add my even sexier dump pipes but i can only fast reply as the frigging normal buttons dont show up on the f**king computer for some reason! :whistling:

nope work computer, im betting that the image for the button is hosted somwhere that is blocked auotomaticly, lots of threads have no pics on this comp too, but not a notification that its blocked jest a big area of nothing

nope work computer, im betting that the image for the button is hosted somwhere that is blocked auotomaticly, lots of threads have no pics on this comp too, but not a notification that its blocked jest a big area of nothing

I feel ya pain, I get heaps of plank spaces on my work pc too :whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...