Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Ah that would explain the flooding.. Thanks for the heads up

Just make sure you don't mount it too close to the anchor coz the chain could drag it down

No real tug feast, Dan is offering advice. This is a forum after all. Not sure if your post was meant to be directed at me or not??

I personally destroyed the brand of clutch in question; I was ripped off and taken on a wild run by the company. I will continue to voice my hate for as long as I can.

I will keep on telling people to steer clear of said brand. There is a fine-line with what I post, I can get away with what I say Re: this clutch as it did in fact happened. I figure, I am offering my 2cents on said brand.

Having driven on an array of singles, OS twins, NPC rebuilt twins and a few Japanese triple plates and a triple plate rebuilt by NPC to twin plate spec.

A 3puck is one of the worst clutches I have ever driven on, as already stated. It has limited streetabilty, it’s costly on driveline as well as hard on driveline.

Tas did the right thing and sold Tristan what he wanted, Tristan wanted a “drift” clutch – However, his application could have been better look after with better options – Again, he wanted a drift clutch and that’s what he got.

Spoken for truth young Joshwaaaa. I know you had a better run from the JB job than I did but a 3 puk clutch for street with the occasional drift session will get old very quickly.....and literally.

Spoken for truth young Joshwaaaa. I know you had a better run from the JB job than I did but a 3 puk clutch for street with the occasional drift session will get old very quickly.....and literally.

Just luck of the draw. I got a good one/lucky one. I would hate to think what could have happened if I didn't. Worst case, could have lost a leg.

No real tug feast, Dan is offering advice. This is a forum after all. Not sure if your post was meant to be directed at me or not??

I meant Tristan. Everyone wanted a piece of him, and I didn't want to be left out!!!

Come to the beat with me?

Of course darling <3

Man. Seriously keep it to PM

NEVER!

Make my rb-bucket go quicker. This little sliding performance hiflow they rave about on here isn't that impressive on my noob-rig

What sort of coin you got? How much hp you want? and what do you want to use it for?

What sort of coin you got? How much hp you want? and what do you want to use it for?

hes flat broke, he wants a gazillionty killer wasps so he can street race.

And he wants frangi's on the back window.

What sort of coin you got? How much hp you want? and what do you want to use it for?

Sunday arvo sprints. I couldnt care less if I rank in the bottom 10, I'm after consistent times. Im also looking at doing Mt cotton next year.

I already have another turbo back exhaust here and im going to buy a trust cooler in a few weeks.

Thinking:

- fuel system

- cam gears?

- ECU? Dr Drift chip??

- Clutch

I would like to think I could get around 220rwkw, around $2k on the 4 points above, more if full ECU

Sunday arvo sprints. I couldnt care less if I rank in the bottom 10, I'm after consistent times. Im also looking at doing Mt cotton next year.

I already have another turbo back exhaust here and im going to buy a trust cooler in a few weeks.

Thinking:

- fuel system

- cam gears?

- ECU? Dr Drift chip??

- Clutch

I would like to think I could get around 220rwkw, around $2k on the 4 points above, more if full ECU

Have a yarn with zenon Josh, Thats about where he's at with some carefully thought out spenshun mods and he has a ball in that flat capper of his.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...