Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Grrrrrrr can't get damn cat out..... it's held in well with studs + bolts. Got the bolts off but the studs it seems are welded to / are a part of the cat.

Any tips?

Do I have to remove the whole back section of the exhaust to get the cat out? I think I just realised this to be true :P

just work with the wiggle room

exhaust is on hangers, should be able to move it back a bit to get the cat out

its a c*nt of a job on my car, thats why i decided i wasnt going to swap the decat pipe in every track day after doing it once

LOL, found dad's old paperwork for the ride on:

He bought it second hand in 1994, and it was old then:

rideon1.jpg

'twas an 8HP apparently (I thought it was less) but that engine blew up.

He bought the new 10.5HP engine in 1998, at the time it was the biggest one we could get that fit:

rideon2.jpg

I'm not sure how old the mower itself is exactly but I did find the instruction book:

rideon3.jpg

If you look down the bottom, you can note the SIX DIGIT phone number.

Now I remember going from 7 to 8 digits some time in primary school, but 6?

Some quick research, and this very informative page tells me that "Brisbane went to 7 digits in 1975". Therefore, we can conclude that the beast is older than 1975. Thats 35+ years!

And note: it is a mini tractor, not a ride on :P. EEESSSSSSS AAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRR!!!!!!!!!!!!!!!!!!!!!!

Look, you can (could) even get tractor attachments for it:

rideon4.jpg

Definitely needs turbo love

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

bugger

we could MAKE a trailer for it

matter of fact, there is a small box trailer in the back yard I doubt has any chance of ever getting road registered. Could convert it to a tractor trailer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...