Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

no, turbo will be from Hypergear (TR43 - G2 trim) thinking an intake manifold/fuel rail from CPC and ecu from nistune. Rest of the setup is what i got lying around, intercooler piping will need to be sent out and made. I'll make my exhaust myself

True. I might ebay spec mine if I get the urge later on.

What pisses me off is that Jessica Watson chick, why do I have to pay my good hard earned money for her welcoming party? Imagine how many police, security guards, portaloos, etc were hired for the event. I'm going to work out how much it personally will cost me and withhold it.

But right now I have Becks and the people at liquorland must have left it in the sun for too long, it tastes flat -_-

Everyone is getting upset over this Jessica Watson chick I don't get it? I think it's pretty awesome what she did props to her. I only found out today who she was lol I was hoping it would be Emma Watsons hot younger sister but apparently not.

Fail

Win

Anyone have any advice for getting seized bolts off calipers/wheel hubs? I've used every f**king socket and breaker bar I have + gone and bought new shit and still can't get the f**kers off... used heaps of the degreasing shit that has worked for me before, it gets in and breaks up the gunk. But not on either of these 2 bolts on my LF brake caliper. Gonna stab a kitten soon if I can't get it off.

Orrrrrr anyone wanna lend me a compressor + air tool kit? :):(

I'd use a hammer tbh. Big one.

Hmmmm it's crazy, I've used hammers on spanners/sockets/breaker bars.

I've tried the old jump up and down relentlessly on breaker bar. All that did was move the car, even with the wheels chocked and handbrake blah blah blah.

My best looking option other than a rattle gun is to get another caliper from a wrecker, and angle grind the bolt/caliper off lol. But I'm not terribly confident that it would work 100%, and I'm not sure I wanna risk damaging other parts in there (the disc etc)

You show me you ring spanner I'll show you mine :(

You sly dog, you know you don't have to ask :)

ravi i have air tools and cordless rattle gun

Dannnnnnnnnn that would be well sick if you'd wanna help a brother out... It seems you're the go-to guy for everyone hahahaha. How does the cordless rattle gun work? Is it essentially a cordless drill? Cause it would wanna have a whole shitload of torque behind it to get these f**kers undone...

Hahahaha hollllllly shit.

The wheel hub is 30mm, I have the socket for that on a ...... 1/2" connector I think.

The caliper is around about...14mm or something... I've got the socket as well on a 1/4" connector.

Is that of any use to you?

i'll have to bring my selection of sockets. Most likely will destroy standard sockets with this tool. PM your number. tomorrow arvo ok with you to do this? i'll be there around 5pm or so.

That rattle gun has nothing on my air powered one. It has a little over double that power

Hahahaha jesus titty f**king christ...... I WANT THAT POWER

*that's what she said?*

Yeah sick I'll send you my number... I'm gonna go have another stab at it now and just see what happens

Yesssssss! Got the left front caliper off! Hahaha so that's one thing off the list.

Still need to replace both rear drum brakes and the stud on the front right... then it's everything I need to do.

Is there anything special about taking the hub off? Have a look at the pic, just socket on and rotate to undo? Or is there some kind of cap there that needs to come off first? I can't tell?

post-58284-1274093483_thumb.jpg

Dumb question - how does it remove? Pry the squashed bit up with a screw driver.... then what?

bring the two "split ends" together with screwdriver/pliers whatever (so it's straight again), then pull it out from the non split end

Edited by Isola

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...