Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

fags what want to waste time keeping the planet good for future generations. pffft.

makes me want to go and shoot a penguin in the face

and not in a good way :)

crap. rain. all day. :-(

I knew the sunlight and warm weather wouldn't last...

whats the weather in qld been doing?

Edited by GTTG
crap. rain. all day. :-(

I knew the sunlight and warm weather wouldn't last...

whats the weather in qld been doing?

Ah rain its good hey.

Weather here has been quite warm for winter.

Get many pics from the other day ?

nope no pics, sorry.

I don't know what to think about the english birds... Almost like Aus I guess... proportion at the top end of the scale is about the same... except maybe slightly less in the middle and more at the lower end... some of the fashions really don't help. theres a few that would look nice, if they weren't trying so hard to look even better (never seen so many fake tans and over applied war-paint in my life).

Morning gentle mangs.

How's tricks ?

Morning Mags. Although I feel that I must point out: 11:02PM is not morning :)

didn't really look too hard

That's what she said

thats another weekend job

That's what she said

I'm boooooooooooooooooooored

That's what she said

don't link apple shit, fag.

+1

I has more greatooo win sausages like last night :)

I want greatooo win sausages :)

makes me want to go and shoot a penguin in the face

I LOL'd hard

I shall endeavour to keep myself occupied

That's what she said

:) top of the mornin' to you, gentlemen.

Morning Geoff, Scarnon?

morning geoff. how is merry old england ?
crap. rain. all day. :-(

I could have told you it would be like that before you went :)

whats the weather in qld been doing?

Been excellent, sunny and not too hot or cold.

I don't know what to think about the english birds... Almost like Aus I guess... proportion at the top end of the scale is about the same... except maybe slightly less in the middle and more at the lower end... some of the fashions really don't help. theres a few that would look nice, if they weren't trying so hard to look even better (never seen so many fake tans and over applied war-paint in my life).

Are there any with sexy accents and tig ol' bitties, just like Colin's sister?

What to watch now. Yay futurama

Futurewin

mmmmm breakfast yumm

post-46752-1275768889_thumb.jpg

EPIC COOKIE TOWER IS EPIC

post-46752-1275861229_thumb.jpg

She likes leaning for some reason :)

post-46752-1275861237_thumb.jpg

Good find! Bet I could teach her a thing or two

Sup mangs. Figured out this morning I misscounted my days to license backness. It is now 5 weeks from today. f**k YOU MICROSOFT EXCEL!

Sup mangs. Figured out this morning I misscounted my days to license backness. It is now 5 weeks from today. f**k YOU MICROSOFT EXCEL!

pfffttt licence smiscence

i have alphabet lady on faceparty :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...