Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Saw your ride this mornin. Hope it all goes well bud. :banana:

Surprised Dan didn't just push it off a cliff and claim it was stolen

It's all strapped up and waiting to be tuned at EFI. Spoke to Dan a few minutes ago.

Surprised Dan didn't just push it off a cliff and claim it was stolen

It's all strapped up and waiting to be tuned at EFI. Spoke to Dan a few minutes ago.

Will be interesting to see what she makes! What are you hoping for?

you're missing a bit...

you're on the right track

Green

-------- > *

Pink

On one hand I agree.

On the other hand though, things will only get better once the green is removed :starwars:

Will be interesting to see what she makes! What are you hoping for?

Standard bottom end, so it would be nice to see 300rwkw, but any improvement on my current 220rwkw will be good.

Standard bottom end, so it would be nice to see 300rwkw, but any improvement on my current 220rwkw will be good.

should see that comfortably at around 15 -16 psi!

you're on the right track

Partial credit??

Green

-------- > *

Pink

On one hand I agree.

On the other hand though, things will only get better once the green is removed :starwars:

haha!! So once green is removed it becomes = pink > *

Standard bottom end, so it would be nice to see 300rwkw, but any improvement on my current 220rwkw will be good.

Should be awesome!

Isola was that you on the side of Albany Creek Rd last night with the bonnet up? I was following someone so I couldn't pull over.

That was me. My AFM has been a bitch lately. I cleaned it and the plug so many times and I just couldn't work out what the problem was!

Got it sorted now though, it was the secondary connection on the strut tower (which I didn't realise it had!!) that was full of sand and dust and shit. Pulled over and flushed it with WD40. Was that you going past in the silver 33 giving a big turbo vent salute? :happy:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...