Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Martin f*cking lol at that thread. If old mate pays more tax then you earn a year i think he should throw me a couple thousand to play with too.

Ravi, baked beans can pressure tester sounds like an awesome tool, air leak anywhere in the pressure side of the system will cause you issues. The other way i have seen for checking for boost leaks is pretty dangerous, it involves removing bonnet, a back road and holding on tight.

Edited by Dan_B

Martin f*cking lol at that thread.

I think Noel is definitely a better Troll than me...

The other way i have seen for checking for boost leaks is pretty dangerous, it involves removing bonnet, a back road and holding on tight.

Keen.

HAHAHAHA I feel like we should try that method

f**k I love skylines. I was down the back end of the warehouse and I heard out at the street the biggest, fattest spool, screeching of tyres, screamer pipe, EPIC atmo bov... and run out and she was gone :( ... but was definately an RB :worship:

just replaced the rear shoes and brake cylinders in the parents car, it shows i don't do much with drum brakes, took me 3 hours to do it.

urgh cant seem to multi-quote with the mobile forum, fail.

@Dan:

A - drums are shit.

B - you had plenty me practice on the xf, should have been able to smash it in minutes.

@Ravi: that's what she said.

@Miso: tfif +11ty

Yeah the iphone version of the forum is severely lacking key features

-Page numbers

-ability to multiquote

-tits

We can fix the last one easily enough

Carpark meets with dodgy folks.

Defected for not being one of the miniorities.

Still have the same defects on my car currently. Couldn't be arsed to get rid of them yet. I've grown attached to them <3

Morning peoples.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...