Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I didn't get one :(

I didn't send it to you. I sent it to [email protected]

Martin

I can pick you up tomorrow if you like. I'm at Albany creek.

Are you sure, it's a bit out of your way?

Would be Me + Dan_B if you do, will shout you drinks or something :thumbsup:

Lack of air flow may cause issues.

That's what she said

Yeah it's all good, you'll be able to tell me how to ge there anyway. I'm on my p's so no drinks for me.

Send me a pm with your address etc, I'll be home around 630 and will come out straight away

You have been denied membership.

Well f*ck you all, I don't like any of you anyway :P

Yeah it's all good, you'll be able to tell me how to ge there anyway. I'm on my p's so no drinks for me.

You can have coke, or non alcoholic beer :thumbsup:

Send me a pm with your address etc, I'll be home around 630 and will come out straight away

Thanks mang, will send you PM now.

So Colon, around 7:30 at the german club?

Edited by Smity42

Off to see Cassie :cool:

Say hi for me.

I dont even know who this Cassie is, hot receptionist I'm assuming.

Slow day is slow. Want to go home, play guitar, do my courses and watch heroes.

Say hi for me.

I dont even know who this Cassie is, hot receptionist I'm assuming.

Slow day is slow. Want to go home, play guitar, do my courses and watch heroes.

Hot and cute. I'd power her link all night long.

Speaking of playing guitar, a dude here is in a band and needs a new lead guitarist. You keen? They play original stuff hard rock/metal. Very riffy stuff apparently. I can pass on your number or email or something if you want?

Edited by Isola

Hot and cute. I'd power her link all night long.

Speaking of playing guitar, a dude here is in a band and needs a new lead guitarist. You keen? They play original stuff hard rock/metal. Very riffy stuff apparently. I can pass on your number or email or something if you want?

I don't have enough equipment lol. Plus I don't think I'm ready for the world as my 6 string arpeggios aren't perfect yet.

Aside from that if I had more time and more equipment I'd give it a shot.

Hopefully that will change with the up coming management meeting

maybe if the new secretary has no job or life..then yeah i can see a 24 hour turn around on membership stuff!

WOOHOOO! Who's in for some of dans sausage.

http://www.sauqld.com/ipb/index.php?showtopic=2993

Keen, but will see how it plays out on the day. Should be ok though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...