Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

any one on here use openoffice on thier computers? Long story short I sent myseld work that I had done at home from openoffice and didnt save it as word format so I cant read them, normally this would be no problem as I would go home and resave them.....but sadly my computer dies this morning! So yeah if anyone has open office and a spare few minutes please please contact me so I dont lose a few days work!

any one on here use openoffice on thier computers? Long story short I sent myseld work that I had done at home from openoffice and didnt save it as word format so I cant read them, normally this would be no problem as I would go home and resave them.....but sadly my computer dies this morning! So yeah if anyone has open office and a spare few minutes please please contact me so I dont lose a few days work!

This might work. Or you can email the file if you get stuck and I can convert and send back to you.

http://katana.oooninja.com/w/odf-converter-integrator/download

any one on here use openoffice on thier computers? Long story short I sent myseld work that I had done at home from openoffice and didnt save it as word format so I cant read them, normally this would be no problem as I would go home and resave them.....but sadly my computer dies this morning! So yeah if anyone has open office and a spare few minutes please please contact me so I dont lose a few days work!

I don't have open office, but if you're going to lose a few days work and no one else can help you give me a yell and i'll just install it and do them for you.

Anyone else getting paid to drink coffee and eat custard tart right now? It's a good feeling :cool:

Earlier I was getting paid to eat pork tonkatsu. Right now I'm getting paid to drink bundy and cokes...

My actual work today has consisted of about 5 mins tapping away on my laptop.

:P

I don't have open office, but if you're going to lose a few days work and no one else can help you give me a yell and i'll just install it and do them for you.

cheers mate, I have some one having a look at it now but if that yeilds no results I will give you a shout tomorrow!

Earlier I was getting paid to eat pork tonkatsu. Right now I'm getting paid to drink bundy and cokes...

My actual work today has consisted of about 5 mins tapping away on my laptop.

:P

You win that one.

Earlier I was getting paid to eat pork tonkatsu. Right now I'm getting paid to drink bundy and cokes...

My actual work today has consisted of about 5 mins tapping away on my laptop.

:P

Nice score! Was the five minutes of tapping to make your post about your day? Because that would be awesome.

New phone is camping ~100km from heathrow, waiting for the airport to re-open. Hopefully will be on a direct flight to brisbane by the end of today :)

Aloha mutherbishes...

So I turned up to BNR just after 9pm, to find.....wait for it....... no one.

WEAK!

Terrorist, McRae, Two-Bob, and I were all there. McRae left probably about 8pm to go do assignments, the rest of us bailed probably about 8:45pm. I was almost home when I got your message.

Colin said to tell you something... but I forgot what it was now.

hey Martin! I cant get any of this shiz to work regarding opening these documents, would I be able to email them to you?

I farking hate computers....and my inability to use them right.

Doing my timing belt and water pump tonight/tomorrow. Fingers crossed for no munched valves :)

Good luck! Did it snap? :(

Thanks kind sir, I owe you beer or icecream or somthing!

No worries at all! The thought of someone losing that much work due to a file type incompatibility is offensive.

No worries at all! The thought of someone losing that much work due to a file type incompatibility is offensive.

If only our IT people felt the same way!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...