Jump to content
SAU Community

Recommended Posts

List of attendies updated

PBK1776

Shane666

Jeffworld2

FIGJAM

R2THEJ

MICOR

GIZZMO

APHRODITE

PINKCESS

RADZ

TKR

SLY-25T

PELAO

punisher6942

BigAmph

NYTSKY

Dave

Bloody hope my cars on the rd for this:) big probs with AFM. anyone here have one like NOW??????

I got 2 x standard R32 GTR AFM's for sale... I'm in thr liverpool area...

  • Replies 93
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Thanks guys:) One is being put in tonight, hopefully it solves the prob:)

Ok re cruise. Please state where you are going to meet... I am not sure if ppl are going to come to the granville maccas so i dont want to be the only one just sitting round waiting:) :blink:

So please please let me know whethr u meeting at crossroads or granville.

Remember that the Granville meet is Maccas on corner of merrylands rd and woodville rd. Then we cruise down to the Crossroads meeting up with the rest opf you in car park out front of KFC.

Thanks

really really hoping my car is bk on road :D

If not, dave im coming with you:0

Yey!!!!!!!!!!!! My car is back!!!!!!!!!!!! :P

Soooo, unless someone posts that they will be meeting at granville, i will not go there i dont think cuase its out of my way to be sitting there for ages and have noone show up there.

So ppllllsssss post if you have nay intentions of meeting aT GRANVILLE maccas by 8.30 am tom or ill just head straight to crossroads.

http://203.84.234.232/amfphp/main/retail.php?m=16&s=F2

Follow this link to get to the location of KFC at crossroads

http://www.crossroadshomemaker.com.au/howtogethere.amx

follow this link to get to crossroads

Below is one possible route we can take

Camden Valley Way & Beech RdCasula New South Wales 2170, Australia

1. Head south on Beech Rd toward Parkers Farm Pl

Go through 1 roundabout 0.7 km

2. At the roundabout, take the 1st exit and stay on Beech Rd 0.2 km

3. Turn right at Campbelltown Rd 13 m

4. Take the ramp onto South Western Fwy 36.5 km

5. Take the exit toward Picton Rd 0.7 km

6. Turn left at Picton Rd 6.4 km

7. Slight left at Mount Keira Rd 17.3 km

8. Continue on The Link Road 3.7 km

9. Take the ramp onto Southern Fwy 23.2 km

10. Continue on Princes Hwy 2.4 km

11. Slight right to stay on Princes Hwy 88 m

12. At the roundabout, take the 2nd exit onto Illawarra Hwy

Go through 1 roundabout 14.5 km

13. Turn left at Clover Hill Rd 0.6 km

Macquarie Pass New South Wales, Australia

I have printed this out a few times so ya'll can have one:)

ill be at crossroads.... my attendance on the actual cruise will depend totally on how wet it is also and having no stereo hooked up in the car leaving me with no music to keep me amused is incentive to not go for a long drive lolz but i will definitely stop in at the crossroads for a visit and to say hi to everyone

GUUYYYYSSSSS!!!! A bit if rain never hurt anyone!! See you at all the crossroads at 11.20am. I will prob be there a bit earlier. Newbys just look out for my black 33 with pink calipers and pink interior:)




  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...