Jump to content
SAU Community

Recommended Posts

hi guys,

im not sure if i need to run low or high impedence injectors for my gtr. has a power fc & the resistor pack is still in the car so im pretty sure its low impedence.

if i take out the resistor pack & run high impedence is there any advantage in doing this?

what style of plug does the gtr have, is it what they call a denso plug?

Link to comment
https://www.sau.com.au/forums/topic/265886-injectors-for-gtr/
Share on other sites

Why don't you find a workshop or tuner your happy with, Pay them for an hour of their time and sort out exactly what you do and don't need for this engine your building??

Not trying to be rude but it would save you alot of headaches if you ask the one person who will ultimately make or break the rebuild your doing.

Just food for thought

Why don't you find a workshop or tuner your happy with, Pay them for an hour of their time and sort out exactly what you do and don't need for this engine your building??

Not trying to be rude but it would save you alot of headaches if you ask the one person who will ultimately make or break the rebuild your doing.

Just food for thought

Agreed.

It seems 'Marko' and 'im late' are the main players getting a rebuild or upgrading their shit at the moment...a new thread for each question and each different component on their engines.

Getting pretty draining.

i apologise in advance as i just found out that the sales rep im dealing with has nfi

the guy couldnt point me in the right direction with impedence or plug... i finally found what im looking for on google

hopefully this thread might help someone else who is searching for the same answer, gtr runs a bosch plug!

pls ignore this thread :-)

high imp in your size requirement would be rediculous. low imp are much better. who the hell runs 800cc high imp injectors ?

Umm every 800cc SARD equipped GTR, same as 700cc SARD (and every other GTR replacement injector on the damn market in 700-1000cc)

Your point exactly would be...?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...