Jump to content
SAU Community

Recommended Posts

Ok well i Have heaps of stuff that has to go so make offers on anything you think you are interested in and you will pretty much get it if the price makes sense obviously although very generous.

My camera has done ok although as there are so many items i may put pictures up as people are interested so i dont have to add heaps of pictures, also if you want better pictures etc i can send to email etc.

Anyway items in list pretty much from most expensive to least

  • NISMO 17's. These rims have no marks at all. Only 2 were ever used. 2 still in boxes. The other two have tyres 235/45/17 on them at about 50% i would say. They have been sprayed black and do not have one chip nor dent on them from a gutter or anything. drilled out for 5 studded cars and came off a R33. Original Genuine NISMO with indented nismo written on each wheel.

  • HKS Super Dragger exhaust. I was told this is a super dragger. It has metal stapped HKS badge but not exact model so i believe this is the super dragger and in ok condition coming off a R33

  • C style Short shift. Please check photo before making offer as it came out of an R33 and unsure if all peices are there as it was ages ago and dont have R33 anymore to test if everything there but pretty sure it is and have pics for you to see.

  • Stock standard shifter for R33

  • Stock standard Intercooler R33

  • Stock Standard Coil Packs R33

  • Stock Standard Fuel Injectors R33

  • Stock rear tail lights in great condition for R33

  • Poineer 10" 650 Watt Max Sub

  • Stock Front and Rear Brake Rotors with heaps of meat on them in perfect condition so save getting your brakes machined or replacing rotors as these are close to new. R33

  • Stock front and rear brake pads with heaps of meat if you rather not buy new from shops... R33

  • Stock side indicators, the thin slim ones that people replace with clear just like i did... R33

  • Stock R33 computer

  • HKS Pod filter in average condition

  • Stock Fuel Filter for R33

  • Stock radio/cd from R33

  • Stock air ratio thingy, the thing you replace with Z32. R33

  • Stock Cam gear and belts and Cover for R33

  • R33 leather manual boot cover

  • 2 Blue and 2 Black Momo seat belt covers with padding in good condition

Will supply all pictures over time. PM me as then i am aware you are interested as i dont check post often.

Oh last of, any RB drivers, have set of "ILUVRB" number plates for sale also in black and white

Thanx

Wheel shots,

Forgot to state they are 5 spoke

Oh and also selling a stock rear spoiler for black R33 and a thing that sits just below boot saying skyline sprayed in black

And over $300 in neons. Under car, stick neons, neon responds to sound, extra cigertte plug adapters, heaps....

post-36498-1239957405_thumb.jpg

post-36498-1239957660_thumb.jpg

post-36498-1239957676_thumb.jpg

post-36498-1239957691_thumb.jpg

post-36498-1239957717_thumb.jpg

Oh sorry, LOCATION is MORNINGTON PENINSULA, VICTORIA

Can also meet anywhere on way to DONCASTER as often travel there.

Everything else can be posted.

As for posting prices, i honestly dont know how much everything worth anymore.

Will call wreckers tomorrow and get prices on all stock parts and then sell 30% less than what they quote as i think that sounds fair. Until then you can make offers and if they seem reasonable i will just sell.

As for the non wrecker items

  • Sub- $20....
  • Exhaust- $250...
  • Wheels- cost me $2200 just for rims 2 years ago... Offers around $1000 i guess
  • C shifter, $50 if all there
  • HKS pod, $40...
  • MOMO covers, $10 a pair...

If i way off tell me. Thanx

Hey, pics are coming. Here are some of the things people have been asking about... Email or pm for specific shots if you want them.

I have to go now and wont be back to computer till sunday arvo so sorry to all the people who have pm'd me. I will get back to you asap and the people who have Pm'd first with offer will get the parts as dont have time now to write back individually and answer questions and offers. Sorry

Pics people have asked for

Air Flow

Injectors (been asked again for pic but pretty sure one already up)

C Shifter

Exhaust (Think 3-1/2 maybe 4". Will measure when home)

post-36498-1240018792_thumb.jpg

post-36498-1240018814_thumb.jpg

post-36498-1240018838_thumb.jpg

post-36498-1240018855_thumb.jpg

post-36498-1240018872_thumb.jpg

post-36498-1240018901_thumb.jpg

post-36498-1240018916_thumb.jpg

Sir RB, they are from a series 1 and all good ;)

All Pm's replied to...

Am a teacher and off on school camp so wont be back till friday so just leave an email if want something. People that i am awaiting money from, will send asap once i return. Thanx

SOLD: Injectors, AFM (money clearing), shifter (only been told its sold...).

Everything has to go... Its all going CHEAP!

are the coilpacks from series 1 or 2??

where they in good working condition?

thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...