Jump to content
SAU Community

R32

Sydneyactionman

By Sydneyactionman,
in Wanted to Buy

 Share

Recommended Posts

Sydneyactionman Proficient

Sydneyactionman

Posted
Posted

I have a 1990 R32 GTR

I'm after the inside window seal from the drivers door located at the top of the door trim, as you can see from the photo is has curled up in the middle & is to short now.

A piece of boot trim from the passanger side. The piece I am after looks very simliar to the the drivers side piece shown in the photo.

2X Front Wheel Studs

I figure the parts should be the same on all models & years

Please let me know if you can help out

post-60944-1240131620_thumb.jpg

post-60944-1240131815_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/266153-r32/
Share on other sites
  • 1 month later...
Sydneyactionman Proficient

Sydneyactionman

Posted
  • Author
Posted
get ur wheel studs new mate... i went 2nd handies and paid the price of them stripping out.

r32 nissans use the same nissan x-trails ..

Hey thanks yes it's not worth me being a tight arse.

Link to comment
https://www.sau.com.au/forums/topic/266153-r32/#findComment-4607792
Share on other sites
familka gtr Experienced

familka gtr

Posted
Posted (edited)

Get new studs from autobahn , they cost like 8$ each .And seal pull it out and get him treatment with heat gun and then stretch him up in the origo size.he will be OK then .

I do have ur rear boot trim in Brisbane 20$ delivered

Edited by familka gtr
Link to comment
https://www.sau.com.au/forums/topic/266153-r32/#findComment-4612143
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...