Jump to content
SAU Community

Recommended Posts

Hi,

I'm fine with wiring up my car stereo system, but when it comes to installing something like this I'm a little unsure, the installation instructions advise which wires, but I have no idea where the wires are located behind the dash....and my soldering iron is not the best either.

Would anyone have time to help install this on a weekend?

Preferably South East suburbs, its supposed to be relatively simple, I can offer something, eg. a bottle of vodka or similar for the time.....

I'm fine with getting the dash apart, its more the which wire goes where problem and soldering :wacko:

Regards,

Gareth

Would anyone have time to help install this on a weekend?

Is this the Ruzic 4wd controller? I've just installed one on my GTR, was quite easy. I'll give you a hand if you like.

Is this the Ruzic 4wd controller? I've just installed one on my GTR, was quite easy. I'll give you a hand if you like.

Yes its the Ruzic 4WD controller :)

If you've got some time that would be great, I'm a bit of a n00b with electronics, but can help if you have an IT problem :ph34r:

Is this the Ruzic 4wd controller? I've just installed one on my GTR, was quite easy. I'll give you a hand if you like.

Thanks a lot for your help!

To summarise, for anyone else attempting the install, its relatively easy, the only little mistake I found was the wires to the switch are listed as "white/brown" on myn it was "grey/brown", quite obvious once everything else is wired up.

My installation was on an R33.

The "G" sensor, that the main plug connects to is located under the centre console, there are two screws next to the seats on the side of the centre console to remove it.

There is also two buttons on the bottom of the handbrake leather cover.

And 3 screws which are visible if you have removed the gear surround which you need to unscrew and the entire centre console comes out.

Under here are 2 black plugs with a lot of wires, the Ruzic controller look diagram describes the colour of the wire on the *right* (drivers side) of the plug (the top plug).

2 of the wires get stripped, we (Wyseman was assisting :P) used the left hand side of the plug to do this, as it was easier, just pay attention to the colour change of each wire, and you will need to remove the outer plastic coating and wrap the controller wire around the wire, solder if you can (I was too nervous about attempting to solder here so used a strong twist and a lot of tape).

1 wire gets cut....and you join as per the instructions.

I re-used the stereo power wire, simply spliced (sniffing?) the power wire from there, and the stock stereo ground (which was unused).

There is also 1 wire which goes to the centre gauge cluster, to the back of the gauges, the EV+ screw of the torque controller gauge has the wire go to it.

I managed to sneak the switch in under the plastic, on the right side of the plastic surrounding the gear lever, facing horizontally...

The controller I velcro'ed to the drivers side of the plastic, well under the dash, you can see but not read it while driving, you have to stop and look at it... putting it where the ashtray goes would have been better but I don't want to hack the dash at all.

EDIT: with the plastic cover that goes around the serial plugs, be warned that there are 4 same-sized screws.

You want the 4 with flat heads, and the tiny nuts, to go through the covers vertically and hold them together.

The 4 longer screws with phillips head are used with the brackets with 2 holes, you use the non-threaded hole to secure the bracket to the front of each serial plug (2 per plug).

You then connect the plugs and run a shorter screw between the outer threaded hole of the bracket to ensure the serial plug cannot be pulled apart...

(I actually used the 4 phillips head screws first, then spent a while trying to work out why the flat headed screws wouldn't fit into the serial plugs properly...)

It's not *that* hard to do but its a little tricky, without some friendly assistance I would have had no idea where to find the g-sensor or where to look for the wires.

Thanks a lot wyseman!

P.S. I considered doing photographs but the last of these controllers are getting sold now so its probably not worth making a proper tutorial...

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...