Jump to content
SAU Community

Coil Pack Question

Buddy

By Buddy,
in General Maintenance

 Share

Recommended Posts

2LV8ETR Mentor

2LV8ETR

Posted
Posted

There are 2 Splitfire types for the R33:

SF-DIS005 RB25DET

SF-DIS008 RB25DET 6/97 onwards

The difference between the RB25DET series 1 and series 2 Splitfire coil packs are the igniters. The series 1 have separate igniters, where the series 2 are built in.

This should answer your question.

2LV8ETR Mentor

2LV8ETR

Posted
Posted
how do i tell if the SII have igniters in them? and if i put them in my SI woul dit work

The ignition system was changed with the Series II. The ignition module was no longer located on the cam covers and was instead replaced by the improved ignition coils and ECU.

I believe you will find that the ECU is different as well as the ECU puts out a positive pulse rather than a negative of the usual setup. The ECU is different to that of the Series I to compensate for the different ignition system among other things.

As for determining the physical difference between the two packs I cannot say. I would suspect that the Series II would be a bulkier item than the Series I. If you had one of each I'm sure you'd be able to tell.

Sorry man, that's the limit of my knowledge......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

      Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...