Jump to content
SAU Community

Recommended Posts

Hi,

Got a bit of a prob, rear passanger side bearing disintegrated, with it the seal, and apparently there's a spacer that goes b/w the bearing and the cover that holds the whole thing together

Can someone supply me with a diagram of how this thing is meant to be put together?

BTW, I'm in PNG, so going down to the wreckers is not an option

Cheers

KB

Link to comment
https://www.sau.com.au/forums/topic/267443-need-88-skyline-diffbearing-diagram/
Share on other sites

In that case it's probably a local R31 with a live axle.

I guess the bearing your talking about is out on the end near the wheel eh!

If this is the case, the bearing you're talking about is just behind the axle mount flange. Correct?????

Cheers, D

And remember, it's a retainer, ie it retains the bearing on the shaft. More importantly, it retains the whole axle in the housing, preventing it (and your wheel) parting company with the car. Don't just bash the retainer on with a hammer. I'm inclined to think that if you need to ask questions on an internet forum, you probably should get someone more experienced to fit the bearings for you.

  • 2 weeks later...

yea if aus r31 will b bw78 diff. will need 2 drop ur centre out and press off the old bearing. then just go 2 a bearing joint and match it up (dunno what auto places u have there?). just normal taper roller/plain bearing or something (cnt remember) nothing special. press new 1 back on and this ring ur talkin about is ur shim, it sets the backlash between the pinion and crown gear. goes between the bearing and diff housing will def need it.

should b pretty straight forward taking it out when looking at it.

take wheels off, slide disks off (floating rear), undo 4 bolt axle flanges, pull axles out, undo diff plate, undo 4 bolts on the bearing cups. then diff centre should just fall out, might have 2 jimmy it out with large screw driver etc...

close-ish just dw about the mini spool part. more stuff on that site\/

http://wiki.r31skylineclub.com/index.php?t...ng_a_Mini_Spool

Edited by OUTATIME

We've got the bearing out, that's not a prob, but my mechanic recons there should have been a spacer holding the bearing in place. and we need the part numbers for the spacer/retainer and the seal

The old bearing was in bits and pieces when we took the cover and axel out...

N

:):D What is it about people posting tech how-to articles and them filling them with crappy mobile phone photos? Even the most basic phone takes half decent pics now, and digi cameras aren't that dear (my son's $70 job takes fantastic photos). Sorry for the rant but I take tech photos and write tech reports for a living and this kind of thing just sh!ts me no end.

Now that's out of my system, I have a Nissan Service Manual, and there are no pics in there showing the rear axle installation. It does, however mention the bearing retainer ring which goes on the inboard side of the bearing. Note this ring is never to be reused, and a new one will be supplied with the bearing kit. Your mechanic is correct - there should have been one. don't fret if you can't find it, as a new one will be supplied (as long as it's not floaring in your axle housing somewhere :banana: )

The photo below shows a Mazda RX2 setup, which uses the same concept as all live axle setups AFAIK. note that the locking collar has been welded to the axle in the photo - not what I'd call good practice, but it's how I got the car. Apparently it was a common fix for early Falcon (c1970's) when the rear axles used to pull out whilst driving.

post-266-1242276165_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...