Jump to content
SAU Community

Swapping Springs Over On Coilover Suspension

R-SPEC
 Share

Recommended Posts

R-SPEC Grand Master

R-SPEC

Posted
Posted (edited)

as above

i have 2 different types/specs of coilovers.

1 is height adjustable and the other is damper adjustable

the height adjustable ones are leaking so i wanna take out the the springs and tops off that set and put them on the other non leaking set

i wanna swap em over because theyre too hard for street use

so the question is, is it ok to change springs/tops over on different shocks?

any help would be great

Edited by R-SPEC
badhairdave Proficient

badhairdave

Posted
Posted

yeah, you can do it easily enough and as you are going down in spring rate you will probably find that the damper is better able to control the spring.

You may have an issue with swapping tops over if the shaft on the shock is a different diameter or the section for the mount is longer/shorter but you won't know that until you have a good look.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      f**king around with the bro
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      Ludenham   44.2 tops day no issues  
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Then today, I went to visit a man with an r33 hat Peter and Road and Race sorted the alignment. As it is being set up for general track/hillclimbs etc it has a heap of caster (7o), less camber than I am used to (1o front and 2o rear, as the caster looks after that in turns without the braking downsides), 3mm front toe out and 0 toe rear. Will see how that goes and track tyre wear to see if it does need more camber, but adjsustment is also limited with nismo arms and adjustable bushes at only 1 end. It does have a bent inner tie rod on the driver's side front but as it came up within spec I'll just leave that as is. So, that is getting close to my chapter of this story....could of tidy ups then a shakedown in early October before it finds a new home.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • Duncan
      Slight brake pedal stutter after new pads

      By Duncan · Posted

      what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
×
×
  • Create New...