Jump to content
SAU Community

Recommended Posts

hey guys getting a new turbo this sat so selling my r33 turbo series 2.

really good turbo for a rb20 or replacemnet for your rb25.

no shaft play, on car now if you wann see it running only tomoro too see it.

has elbow, 33 actuator, bolts if needed, lines if needed for extra $$$$.

i also have a remapped dr drift ecu to suit r33 turbo, full exhaust, fuel pump,.all you need is a tune from dr drift at your looking at 190kw

both items for $600

or offers for each pm me guys iam i n vic i can post anywhere.

hey guys getting a new turbo this sat so selling my r33 turbo series 2.

really good turbo for a rb20 or replacemnet for your rb25.

no shaft play, on car now if you wann see it running only tomoro too see it.

has elbow, 33 actuator, bolts if needed, lines if needed for extra $$$$.

i also have a remapped dr drift ecu to suit r33 turbo, full exhaust, fuel pump,.all you need is a tune from dr drift at your looking at 190kw

both items for $600

or offers for each pm me guys iam i n vic i can post anywhere.

hey cant pm how much for just the turbo?

Hey im from Canada and looking for a turbo local but its not working out. Would there be a chance you would ship to Alberta Canada, Postal Code is T0M-0J0 and im in Blackfalds Alberta.

Thanks for any help. would only need the turbo.

PS. any idea if there are any differences between a series 1 and 2, as far as the oil/coolant line go? I have a blown series 1 right now that i want to replace quick and easy..

[email protected] or PM

Kyle

Hey im from Canada and looking for a turbo local but its not working out. Would there be a chance you would ship to Alberta Canada, Postal Code is T0M-0J0 and im in Blackfalds Alberta.

Thanks for any help. would only need the turbo.

PS. any idea if there are any differences between a series 1 and 2, as far as the oil/coolant line go? I have a blown series 1 right now that i want to replace quick and easy..

[email protected] or PM

Kyle

no way man i dont even know how to post to canada..ill ask the post office tommoro. will let you know

hey mate. Any pics of turbo? kms? how much to post to 4814?

P5230003.jpg

does not come with the hks actuator or the dump pipe

it came off a 100k car and on my car for 3,000km great turbo you wont have a problem

post shouldn't be too much iam guessing $25

Edited by R32 DRFT4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...