Jump to content
SAU Community

Recommended Posts

Greetings all,

We have stripped out the interior on a 1987 Silhouette, the following interior trim items are up for sale.

All items located in Albury N.S.W, prefer pickup on larger items, courier/postage can be arranged at buyers expense.

Make an offer.

Contact via PM.

01_rear_door_card_right.jpg

$40 Right hand rear passenger door card. Condition-used

02_rear_door_card_left.jpg

$40 Left hand rear passenger door card. Condition-used

03_rear_back_rest.jpg

$60 Rear back rest. Condition-used, sun faded on head rests, could use a good clean.

04_rear_back_seat.jpg

$60 Rear seat. Condition-used, could use a good clean.

05_roof_lining.jpg

$5 Roof lining. Condition-used, quite filthy, no tears, includes all cross roof bars to pin it in place.

06_parcel_shelf.jpg

$10 Parcel shelf. Condition-used, holes hacked out (by previous owner) to fit 6x9 speakers.

07_centre_console.jpg

$15 Centre console. Condition-used, few scratches and marks, volume adjust on headphone output missing knobs.

08_A_pillar_trim.jpg

$5 A pillar trim. Condition-used, left hand trim missing lower section where it would meet flush with the dash.

09_B_pillar_trim_lower.jpg

$10 B pillar trim, lower half. Condition-used, few scratches and marks.

10_B_pillar_trim_upper.jpg

$10 B pillar trim, upper half. Condition-used, few scratches and marks.

11_C_pillar_trim.jpg

$10 C piller trim. Condition-used, few scratches and marks.

12_roofline_trim.jpg

$10 Roof line trim. Condition-used, few scratches and marks.

13_handles.jpg

$15 3x Roof handles. Condition-used, deep scratches and marks.

14_front_overhead_light.jpg

$10 Front overhead light. Condition-used.

15_middle_overhead_light.jpg

$5 Centre overhead light. Condition-used.

16_auto_gear_stick_surround.jpg

$15 Auto gear stick surround. Condition-used, ink stain on front, scratched and marked.

17_centre_dash_surround.jpg

$15 Centre stereo surround. Condition-used, scratched and marked.

18_ash_tray.jpg

$5 Ash tray. Condition-used, scratched and marked.

Make an offer.

Contact via P.M

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...