Jump to content
SAU Community

Recommended Posts

Wondering if anyone else has this problem and what they did to fix it?

Basically when starting the engine from cold it takes about a minute or 2 before the thermostat opens.

During that time the engine feels really rough, when pushing the accelerator the engine starts to stutter when going beyond a certain rev range, until the thermostat opens (ie the temp gauge starts to move). Then it is fine.

It doesn't really bother me too much as it helps me warm up the car slowly.

Car is R32GTR with apexi pods and catack exhaust+cam gears.

I've also started to notice that it pings as well until the thermostat opens.

Is there something going on I need to fix quickly?

Link to comment
https://www.sau.com.au/forums/topic/272491-engine-feels-resticted-when-cold/
Share on other sites

my 33gtst is the same. when its cold if i accelerate too hard it sounds like its going ok but is jumping around like its gonna blow up. i am guessing that my old mechanic put the wrong oil in cause it kinda feels like the pistons arent moving smoothly. i am possibly completely off but just my guess.

This is a factory feature of the ECU to protect your motor when it is cold.

Until you have reached the expected operating temp it places a number of restrictions on the level of advance of the timing and other paramaters to stop you from working the engine too hard while it is cold.

If it runs well when it has warmed up then all is good as it is only doing what it was designed to do - it does become a problem though if it does not run crisp after it has warmed up and that is when there is something wrong that needs investigation and fixing.

You should just let your car warm up a bit anyway just before driving (On cold mornings).

I usually let it idle for about 2-3mins to get the engine oil circulating then start driving and keeping it off boost for about 5-10 mins of driving (light boost is ok) to get all other fluids going.

Then the car is fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
    • what sort of caliper are they? If they are a slider and you gave everything a good clean, you might need to regrease the pins. My guess though is they will come good after some abuse as suggested above
    • I don't know what you should expect with an LS, but the oil pressure sounds terrible, sorry. As for the brakes, you can get fade from the pads not just the fluid, although generally that feels like a wooden block not doing anything while fluid feels like an oh shit there is no pedal so you can generally tell. What pads are you running front and rear?
    • Went over my datalogs on a whim and noticed a worrying combination of events. High RPM High Temperature Low Oil Pressure Knock Retard I bought some 10w-60 because I actually think this will be better going forward given track temp is 125C and 10-40 will actually be thinner in those environments. I know I had a leak but it's not entirely sure how much pressure loss can be attributed to that. The knock retard does correlate with all of the above. When it's not present oil pressure is higher. And by 'low' I mean at 6800 RPM the oil pressure was recorded as low as ~35psi pretty constantly. Which is obviously very not good. I'm hoping that thicker oil that ISNT LEAKING will result in a bit more pressure when I need it. Also in the last session I got a very spongy break pedal. I bled the lines as the car is on jack stand right now with the wheels off and I noticed... no air in the lines? Maybe the tiniest bit of tiny frothy bubbles for the first 0.1 seconds of bleeding the whole car? The breaks did come back to me after I backed off (and felt fine driving normally). Doesn't appear to be any leaks anywhere that I can see. Any thoughts on that?
    • Solution, run shitter tyres. Let wheel spin be your weak link 😛
×
×
  • Create New...