Jump to content
SAU Community

Recommended Posts

Any specials on at the moment for a set of QFM A1RM brake pads for a r33 gtr with brembos. Will need front and possibly 2 sets for the rear.

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

Any specials on at the moment for a set of QFM A1RM brake pads for a r33 gtr with brembos. Will need front and possibly 2 sets for the rear.

Hi mate,

Brembo A1RM fronts are $179 for the axle set (RRP $229) and $149 for the rear axle set (RRP $199).

Also two or more axle sets of pads (ie front and rear) gets free shipping.

Regards,

Greg

QFM A1RM Fitted to JZA80 Supra!

Thought I'd add my 2c.

I recently made over my brakes with some braided lines, slotted rotors and the QFM A1RM pads. It wasn't just a pad change so I can't compare directly with the old set up however I'm bloody impressed with how the car pulls up now and I believe a lot of that is down to the new pads. The brake fade is quite minimul and significantly better than the stock Toyota pads I had on it previously. Slam on the brakes and it bites hard, time and time again. So much so that I sometimes feel if it pulled up quicker my face would somehow detach from my head and hit the windscreen like some weird crossover film between 'Gone in 60 seconds' and 'Face Off'. Unlike my old setup these certainly give me a sense of confidence through the twisties!

Either way, QFM A1RM pads = WIN

http://www.supraforums.com.au/forum/showpo...mp;postcount=64

Hi Tim,

Yep, got front and rear and on the shelf. Easiest way to order is to give us a all on 1300 884 836 and do credit card over the phone, or else PM me your details, full name, delivery address (preferably a work or business address!!), contact number and email and I can fire you through an invoice with direct deposit details.

Regards,

Greg

QFM are a cheaper alternative to Ferodo DS2500!

I just got the QFM A1RM's and they went well at sandown. Greg was very helpful and delivery was only 2 days.

Very cheap for $130. I don't think I'll be spending big on pads again after how they performed at Sandown.

I will monitor the wear but I get to about 220kmh before jumping on the brakes and they felt similar to my DS2500's.

http://www.skylinesaustralia.com/forums/in...t&p=4916919

QFM A1RM - JZA80 Supra with upgraded 4/2 pot brakes!

Well said and i couldn't agree more. I have been running with QFM A1RM pads in my RZ Supra (4/2 pot) for about two months now and i have not looked back. I previously had Project Mu's and for street and the odd track day i would not recommend anything other than the A1RM's. A fantastic, excellent performing pad from the moment you leave the garage!

http://www.supraforums.com.au/forum/showpo...mp;postcount=74

I understand this is a for sale thread and therefore the vendor has every right to include favourable testimonials from happy clients. However prospective purchasers should be aware that how you define "light track work" may influence how satisfied you will be with the A1RM pads.

Another discussion is here for those who are interested: http://www.skylinesaustralia.com/forums/Ov...1r-t294727.html

Today I went to Winton for the second time with my S14. It has R33 GTS-T brakes all round with stock rotors and QFM A1RM pads all round.

The last time I came and for the first two sessions today the brakes were great however around half way through the day my pedal started going soft and then began to studder. I came into the pits and had a look at the front discs. They were dark and had heaps of pad material spread over them. The near new (at the start of the day) front QFM pads were now down to indicators. The backs however were fine.

My experience with the A1RMs has been pretty average - bedded in with the basic 10x 100km/h-0 stops then took them up to Mallala. Mallala is notoriously hard on brakes with hairpins at the end of two straights. First lap fine. lap two stopping from 180 into the hairpin brakes faded to zero whilst still going 80+, so ended up deep into the gravel.

Perhaps they needed more bedding, as during the rest of the day they **just** held up but still got really soft and felt very unreliable after lap 2. Having run the Ferodo DS2500 before they are (in my limited and personal opinion) *not* comparable - I've never had any problems with the ferodos even with much less bedding in.

in fairness I have heard good things from people who have raced on QFM track compounds, and everyone who uses the A1RM on the street seems happy too, so just make sure you are getting the right advice for your application.

For ever one person who said they've "overheated" them (which as I explained is a bit of a fallacy anyway), I can quote 20 threads or posts where people have been extremely happy with them.

Their biggest problem is (as some body else alluded to) is that that put them in the car, then hit the track straight away. You can get away with that with a dedicated track only pad, not not a street/track pad like the A1RM. Their other big problem is that most of them aren't comparing apples with apples, their comparing the A1RM to pads of far higher performance, when they should be comparing the QFM Comp pads to those.

The A1RM is a Ferodo 2500 equivalent, that is, a pad which is 100% streetable, but still capable of like track work, and that's exactly what it is:

http://www.skylinesaustralia.com/forums/in...t&p=4138203

http://www.skylinesaustralia.com/forums/in...t&p=4141983

http://www.boostcruising.com/forums/index....mp;p=1282506286

http://www.aus300zx.com/forum/showpost.php...mp;postcount=13

http://www.aus300zx.com/forum/showpost.php...amp;postcount=9

http://www.opelaus.com/forums/showthread.php?t=19733

http://performanceforums.com/forums/showpo...mp;postcount=62

http://www.supraforums.com.au/forum/showpo...amp;postcount=2

http://nissansilvia.com/forums/index.php?s...p;#entry5383135

http://www.opelaus.com/forums/showpost.php...mp;postcount=10

If people need pads for high end track work, then they wouldn't be running a Ferodo DS2500 anyway, they'd run something like a 3000, which in the QFM range would be a Comp9. I'm certainly not phased about a few negative comments from people who've hit the track on sticky rubber and wondered why a pad they could've put in their grandmothers 180B to drive to the shops on a zero degree morning didn't perform like a $600 race pad...

But, anything higher than A1RM is a compromise on the street (like any pad is, be it Ferodo DS3000, Project Mu's H16-03, etc) in that they have rotor wear and noise that is too high, and cold (emergency) bite that is too low. If people want to run those pads in their street car, that's fine, but we're certainly not going to recommend it.

So, I still 100% stand by the QFM pads, in that if people come to us asking for a street only pad, it's HPX. If people want a track pad, but say they still want to use the pads on the street, then it's the A1RM. And if people want a track only pad, or a pad that they're prepared to change to in their daily once they get to the track, then it's the Comp9.

Any negative feedback needs to be not of the product, but rather of which product they chose. I personally run the A1RM in the rally car, and I can link another 50 forum posts of people who run the A1RM on the track, and love it.

For reference Comp pads for the Sumitomo Nissan Calipers are $179 per axle set front or rear, and $229 per axle set for the Brembos.

  • 2 months later...

No dramas, just also I started a new thread which included the range of comp pads for those that needed more than A1RM:

http://www.skylinesaustralia.com/forums/Qf...ak-t295467.html

Cheers,

Greg

I ask please that all future posts are directed to the new thread, which includes updated pricing and also the Comp pads, for those after more than A1RM:

http://www.skylinesaustralia.com/forums/Qf...ak-t295467.html

Thanks,

Greg

  • 2 months later...



  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...