Jump to content
SAU Community

Recommended Posts

R33 with 3582r (i will check housing size 2moro for you) 18psi but with 264 cams.

Fuel reg on a r33 is good for high 300rwkw so your reg is not the issue.

post-34927-1245240645_thumb.jpg

Edited by URAS

Yeah, thanks for that. Doesnt matter what gear youre running , it all comes down to a proper tune doesn't it? Funny thing is this guy has one of the best reputations in Melbourne and the results to prove it, but i highly doubt that he tuned my car. Anyway i will post both dynos once i get it retuned elsewhere.

It's put in 4th gear so the tuner is able to tune it.

For example, you would not be able to tune a car in 1st gear because power just comes on way too quick.

Yes it does matter what gear you're in, 1st and 2nd gear will have much different power graphs compared to 4th gear.

Take it to another tuner to get a second opinion. Maybe something was wrong with the car (i.e. detonation) so the tuner had to pull timing out of it, hence the low power?

Maybe there's carbon build up in your engine causing pinging, or a hot spot on the piston.

Take it to another tuner, if he tells you he couldn't pull anything more than 250rwkw without it pinging of its tits, then somethings wrong with your car.

The fun and games begin.

Yeah thats exactly what im going to do. He said everything was fine, that there werent any issues and was actually quite happy. Its not that i want more power, cause its fine the way it is. Its just that i believe that with this set up (barring any issues such as the ones you mentioned) the car should have pulled more than it did. As i said i really got the impression it was done in rush to get the car out of there, and im sure it wasnt tuned by Mark himself.. I'll be booking it in this week sometime elsewhere..just for peace of mind!

got same setup, apart from I got the 0.82 A/R. I have a VERY conservative tune (f#$k all timing, and running rich, knock doesnt go over 15) and I made 312 rwkw at 17 PSI.

I suggest you go see another tuner.

the 0.82 makes 300 easy the 0.63 does not.

Edited by URAS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...