Jump to content
SAU Community

Recommended Posts

I got stickered :D

Cops reckon my exhaust is less than 100mm from the ground so *slap*!

i needa take my screamer and de-cat out, adjust my ride height and i needa ask

Can i borrow someones standard rims with decent tread for pits? Will be going over next week and i hope i don't get royally raped :)

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/
Share on other sites

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

ah dont stress yourself about it. I got done for the same thing recently. I got an awesome inspector at Welshpool and he passed me with heaps of defects still on there. At the end of the day you should prepare for the worst and hope you get a nice inspector.

Have you checked that the exhaust hieght is ok. The cops gave me a flick knife to test my exhaust height. It was probably 80mm from the ground

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4664124
Share on other sites

^^WHS

100mm from the lowest point with a fully loaded car, so if your at 110mm you might still be considered a little too low by the cops.

Also something like 400-500mm from the lowest point of the headlights or something, I never pay much attention to that one.

Basically, if its lowered enough to look good its too low.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4664665
Share on other sites

I'm pretty sure it does, had a few mates fail because their kits scraped.

I've also heard that even a wire hanging down counts, because if it's for a fuel pump or something, it rips going over a speed bump, the car will suddenly be inmovable causing headaches for everyone. That's what I've heard anyway.

Point is, kits are included in the too low rules.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665426
Share on other sites

Yer i work at DPI, but that doesnt mean i will get a nice inspector.

Rhys - yeah i have coilovers and will just wind 'em up and take my screamer and de-cat pipe out.....might come cruising tomorrow night not sure yet

ADR rules state the you are not allowed to have different rim width front & rear unless your car came with different rim widths from factory.

Anyways, cheers for teh replies, i'll get back to you tomoro, im sleepy now :D

hehe ciao

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665584
Share on other sites

Stick with the 100mm from the lowest point of the car rule nic, otherwise fools with 20" rims on their fully sick honda accord Si's that are FAR too low will be more legal than an dumped XA falcon (for instance) with standard 12-slotters.

mates escort pano's lowering block u-bolts were 120mm from the ground, and had like 14x8 custom jelly beans. coppers sent him on his merry way. cop measured a brick that he found to around 100mm and stuck it underneath...

gotta love country cops. normally don't spell it with an 'o', but 'flamin mongrelry' cops doesn't make sense.

Edited by Dorigecko
Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665609
Share on other sites

Yeh, when it comes to ride height, 100mm is the lowest point of the car. That's for everything (kits, cats....mmm kit-kats).

My mate just took his R33 over the pits and he got failed on his rims being too big (R33 gts-t with 19x8.5s all round), and having a spoiler on the boot but not having a brake light in there (as u need a brake light at eye level so they). However, i have taken the spoiler off my car, as you know Rhys.

I might come just to the meet point tonight for the cruise....im sick as a dog atm so i'll see

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665975
Share on other sites

Unlucky man, I almost got yellowed the other day cause the cops were saying my tyres were to big.....lucky for me it started to rain and they went 'f**k it' :down:

Sorry to highjack, but.....

Are 235's on the front and 255's on the back to large for a R32 GTS-T??

I mean, it is right on the guard, and may even stick a mil over....

Edited by Douse
Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4666065
Share on other sites

Yeah Id say it is.

What are the widths of your wheels?

Your not supposed to go with anything much wider than the widest that came with that car.

So you can argue that the GTR came out with 8" wheels and try get away with say 8.5"?

Any wider and it's too wide unless you get permits/engineers.

Sad but true.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4666116
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...