Jump to content
SAU Community

Recommended Posts

I got stickered :D

Cops reckon my exhaust is less than 100mm from the ground so *slap*!

i needa take my screamer and de-cat out, adjust my ride height and i needa ask

Can i borrow someones standard rims with decent tread for pits? Will be going over next week and i hope i don't get royally raped :)

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/
Share on other sites

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

ah dont stress yourself about it. I got done for the same thing recently. I got an awesome inspector at Welshpool and he passed me with heaps of defects still on there. At the end of the day you should prepare for the worst and hope you get a nice inspector.

Have you checked that the exhaust hieght is ok. The cops gave me a flick knife to test my exhaust height. It was probably 80mm from the ground

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4664124
Share on other sites

^^WHS

100mm from the lowest point with a fully loaded car, so if your at 110mm you might still be considered a little too low by the cops.

Also something like 400-500mm from the lowest point of the headlights or something, I never pay much attention to that one.

Basically, if its lowered enough to look good its too low.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4664665
Share on other sites

I'm pretty sure it does, had a few mates fail because their kits scraped.

I've also heard that even a wire hanging down counts, because if it's for a fuel pump or something, it rips going over a speed bump, the car will suddenly be inmovable causing headaches for everyone. That's what I've heard anyway.

Point is, kits are included in the too low rules.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665426
Share on other sites

Yer i work at DPI, but that doesnt mean i will get a nice inspector.

Rhys - yeah i have coilovers and will just wind 'em up and take my screamer and de-cat pipe out.....might come cruising tomorrow night not sure yet

ADR rules state the you are not allowed to have different rim width front & rear unless your car came with different rim widths from factory.

Anyways, cheers for teh replies, i'll get back to you tomoro, im sleepy now :D

hehe ciao

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665584
Share on other sites

Stick with the 100mm from the lowest point of the car rule nic, otherwise fools with 20" rims on their fully sick honda accord Si's that are FAR too low will be more legal than an dumped XA falcon (for instance) with standard 12-slotters.

mates escort pano's lowering block u-bolts were 120mm from the ground, and had like 14x8 custom jelly beans. coppers sent him on his merry way. cop measured a brick that he found to around 100mm and stuck it underneath...

gotta love country cops. normally don't spell it with an 'o', but 'flamin mongrelry' cops doesn't make sense.

Edited by Dorigecko
Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665609
Share on other sites

Yeh, when it comes to ride height, 100mm is the lowest point of the car. That's for everything (kits, cats....mmm kit-kats).

My mate just took his R33 over the pits and he got failed on his rims being too big (R33 gts-t with 19x8.5s all round), and having a spoiler on the boot but not having a brake light in there (as u need a brake light at eye level so they). However, i have taken the spoiler off my car, as you know Rhys.

I might come just to the meet point tonight for the cruise....im sick as a dog atm so i'll see

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4665975
Share on other sites

Unlucky man, I almost got yellowed the other day cause the cops were saying my tyres were to big.....lucky for me it started to rain and they went 'f**k it' :down:

Sorry to highjack, but.....

Are 235's on the front and 255's on the back to large for a R32 GTS-T??

I mean, it is right on the guard, and may even stick a mil over....

Edited by Douse
Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4666065
Share on other sites

Yeah Id say it is.

What are the widths of your wheels?

Your not supposed to go with anything much wider than the widest that came with that car.

So you can argue that the GTR came out with 8" wheels and try get away with say 8.5"?

Any wider and it's too wide unless you get permits/engineers.

Sad but true.

Link to comment
https://www.sau.com.au/forums/topic/275292-stickered/#findComment-4666116
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...