Jump to content
SAU Community

Recommended Posts

Just making a point here...what's wrong with the good old single meet-point & a time for a cruise??? It's fair enough if a few people from the same area want to meet up to head to the cruise together & discuss it in the thread, but separate meet-points for the same cruise? Never seen it done like this....

Just making a point here...what's wrong with the good old single meet-point & a time for a cruise??? It's fair enough if a few people from the same area want to meet up to head to the cruise together & discuss it in the thread, but separate meet-points for the same cruise? Never seen it done like this....

Then you haven't been on a particular e-tuned club cruise then.

Then you haven't been on a particular e-tuned club cruise then.

Yeah eTuned do heaps of this don't they?

N.O.R. meets mean that whever runs from there will pretty much spend their entire night just driving along the freeway man. That, and the dudes who come from way north quite often end up making their own meet points prior to the cruise anyway.

Hope that helps =]

Ok, quick note; there's apparently the "ryding dirty cruise" that night as well, meeting at Citywest. They're meeting at 8:30, leaving 9:30, since we're starting later, and to avoid confusion, if they're inside - we'll take outside, if they're outside - we'll take inside.

Make sense? Open to suggestions here.

New thread to clear this all up (Thanks Rhys)

Cruise for friday night, as in tomorrow =]

Meet;

N.O.R.

Citywest carpark, 9pm meet, 9:30 depart

S.O.R.

Leach Hwy McDonalds, Mellville, 9pm meet, 9:30

Have fun,

Tim

BTW Tim, who's in charge with the S.O.R. meet point?

Tim, it's done and organized. Just leave it as it is. Too late to change anything.

Everyone meeting NoR, look out for Tim's blue R33 with gold vynals down the side, and I'll have my silver R33 there as well. Rydin' Dirty is a Ford club (I think. Bogan V8s anyway) so just look for all the Skylines/imports and come park with us.

SoR people, park with Tobin, white R33 with blue [LULZORS] plates. Again, look for all the imports.

And Tim, just have a single meet point next time, it's much easier that way.

damn, cruises are always on when im alredy doing something.

-just for people that dont know, if u wanna 'cruise' go on this one, if u wanna see LOTS and LOTS of skids4thekids then take the rydin dirrty one.

Supras love it sideways! I know mine does :P

If you know how to drive your car and know it's limits, then nothing is 'too' dangerous.

too risky for me hehe number of high powered cars all tailing each other in the wet hehe didnt want to risk it and no my supra prefers the freeway hehe not sideways

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...