Jump to content
SAU Community

Recommended Posts

  • Replies 477
  • Created
  • Last Reply

Top Posters In This Topic

can anyone get these made up?. i would love that set up on my 33gtr, or is anyone selling one?. bernie

Im having one made up along with a slightly different design.

Can get more made but shipping would be a pain/expense

I got a price on them which I think were 400-500 for fronts alone.

The local 'race brakes' are only 150 for fronts, my mate who was doing 1:07 at wakefield in a stock r32gtr did back2back testing with a no. of pads including some jap brands and bendix ultimate, in terms of braking power and wear the race brakes came out on top.

If anyone is interested I can find his email and post it here?

Bernie - that is a custom job BUT the apexi n1 system is the same with 2 x 3inch pipes and straight off the shelf

cheers marko, we dont really have exhaust people here that can mandrel bend and supply silencers of that qaulity, what would one cost made in oz and shipped to me..lol any takers.lol

my hks preist would probably give me 400 uk back to spend

Edited by rockabilly

To get a full system done in 4inch including front pipes is approx 4k aud, now to run 2 x 3 inch pipes I'd assume would be more than as it is essentially 2 exhaust systems + shipping which I would think is 500 aud.

Bernie, what's the latest with your donk :merli: nothing worse than an engine failure, other than a funeral

I got a price on them which I think were 400-500 for fronts alone.

The local 'race brakes' are only 150 for fronts, my mate who was doing 1:07 at wakefield in a stock r32gtr did back2back testing with a no. of pads including some jap brands and bendix ultimate, in terms of braking power and wear the race brakes came out on top.

Try Racer Industries in Bris. Mine cost $276/pair. The 4-500 sounds like some more serious Mu pads.

Edited by Scooby
  • 2 weeks later...

quick update:

my new brake setup feels phenominal...the combination of refaced factory rotors, 'race brakes' pads & motul factory line brake fluid gives me all the confidence i need, dont know how long they would last on the track though with over 400awkw :D thats ok, i'll just turn down the wick on track days (if/when i get out there)

for the 1st time, i activated my abs with fark all pressure on the pedal haha

i have noticed that my pedal sinks lower to the floor though than previously, is there an adjustment to bring in the contact point a bit earlier?

cost. if i upgrade my braking system though, i will get k-sports all around which will set me back about 4k.

refaced discs = $100

f&r pads = $300

brake fluid = $70

i also dont think i need huge brakes for the street - the likes of duncan who race in production advises that the factory gtr brakes are quite good when setup right.

i know with the power i have i should get bigger brakes - for now though, im wrapped & dont see the requirement :D

come to think of it - if i ever break this box like i did in my other gtr, i'd probably just get another gtr box exchange unit...these days u can get them for under $1000.

what is the cost to get an os gearset fitted in a box (i'd do the r&r myself)?

well its $ 2,848.10 + shipping for the 5 gear kit from RHDjapan at the moment, plus what ever it costs to have it fitted into the box/replace synchros/bearings (i remember something about the R32 box needing some R33 parts as they were stronger/better?)

Well, if you break one and spend another $1000 on another stock unit it makes sense at least to me to get the upgraded box cause the next stock one will just break again. That's my thinking anyway

when I enquired for my box I think it was something like 1500?

Then of course a donor box (350 or so for a worn out one) and a gearset (price of course depends on how wild you go)

well if it was going to cost me 3kish i'd definitely take that path. that is very cheap!

i should speak to terry @ award diff for a price on fitting the gearset.

i always thought it was up around the 7k mark?

apparently the input shaft also needs to be upgraded as well on the r32.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...