Jump to content
SAU Community

Recommended Posts

Hey guys,

I'm going to be picking up an S1 cluster for my GTR this weekend as the S2 doesn't work properly, issues with the electricals or something causing the ODO and fuel guage to not work properly. I am wondering how hard it is to swap these out? Is it a case of take out the dash undo plugs, install new one put back together and go?

-Chris

Link to comment
https://www.sau.com.au/forums/topic/278595-new-cluster/
Share on other sites

hehe yeah. I had done it once with my ole' VL many many moons ago, just not sure about the dash setup for the R32's. I am wondering aswel, being that I have an S2 cluster in there at the moment, would I have to get it calibrated for the S1? Or you think it's likely it was never done for the S2? Just so as the speedo is not out at all ..... Guess the easiest way would be to speed test next to another car heh

Edited by stormtrooper
Link to comment
https://www.sau.com.au/forums/topic/278595-new-cluster/#findComment-4706922
Share on other sites

  • 2 weeks later...

Okie dokie, finally got around to installing the new cluster today (had to switch out some of the bulbs from the old one but no biggie) and I have noticed 2 things. The water temp guage does not work (when you turn the ignition to accessories it maxes out then when you kick over ignition it goes flat) and the rev tacho is not working. However ODO and trip counter now working which is waht I wanted. I have put the old one back in again for now.

I was wondering, what would be causing this issue? Would it be the PowerFC? Because it was originally calibrated for the S2 cluster? And then of course would I need to get it recalibrated for the S1 ?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/278595-new-cluster/#findComment-4735647
Share on other sites

The one that is currently installed is the S2 and the one I was installing is a S1 cluster, which the water temp and rev tacho don't work in at the moment. I'm only replacing the cluster because the S2 I have at the moment doesn't have a working odometer or trip counter, the ODO I need to keep track of for me log book.

Link to comment
https://www.sau.com.au/forums/topic/278595-new-cluster/#findComment-4738351
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A HICAS fault really should not cause the engine to go into limp mode. These cars are so old that the systems barely talk to one another. The thump might be the lockoff solenoid valve for the HICAS (the safety valve) getting closed, to lock the rear wheels "straight". I say "straight", because when my HICAS used to shit itself before I took off and nuked it from orbit, it would lock up with the rear wheels wildy non-straight and you'd need 45° of steering wheel to drive straight. Take off and nuke it from orbit. First step is to pull the smaller of the two plugs out of the HICAS CU. See if it stops misbehaving. You can also (whilst leaving it plugged in) try to get the HICAS CU into diagnostic mode by doing the pedal dance, or by connecting a CONSULT capable diagnostic reader into the car and seeing what it has to say for itself. Can't do either of these with it unplugged though. 1st gen HICAS is a ballache. I would do a complete delete. I did do a complete delete.
    • Ah. I dunno why, but I skim read your earlier post and thought the manual switch was to force it on, not force it off. I'd be tempted to have both. So, your two in series, and another in parallel with those. Or, a master arm switch, followed by the manual force on and the thermo in parallel. 6 and 2 3s.  
    • Yeah been doing it in an x shape. Do you reckon it's worth putting guide coat early where the filler isn't sanded down completely smooth? Reason I ask is because as I'm sanding it one part might be level which I don't need to sand anymore but the other part might be high so I can just focus on that instead of sanding across the whole repair area. I wonder if the putty is too thin, though the area is almost completely smooth before I do it as I've already put filler prior.
    • Just 2, and inline. One switch temp related other switch driver controlled.   I'm nearly in my head back to Arduino land for it...
×
×
  • Create New...