Jump to content
SAU Community

Recommended Posts

Hey guys,

I've noticed recently that my car takes a long time to start.

I've put on a turbo, intercooler, had a quick tune at gavin woods, so somewhere in there something has happened.

Everything works perfectly, but i used to turn the key for a quarter of a second and get it started, now i'm sitting there for a few seconds while the starter motor keeps trying to get it started, sorta like if you have a low battery, but i've only had this battery a few months and i've done a few highway runs so i know it would have good charge (and it's not doing 'slow' starter motor sounds).

What could this be? I've tried searching for a few terms but can't find anything helpful.

Thanks :D

Link to comment
https://www.sau.com.au/forums/topic/278922-r33-takes-long-time-to-start/
Share on other sites

Hey guys,

I've noticed recently that my car takes a long time to start.

I've put on a turbo, intercooler, had a quick tune at gavin woods, so somewhere in there something has happened.

Everything works perfectly, but i used to turn the key for a quarter of a second and get it started, now i'm sitting there for a few seconds while the starter motor keeps trying to get it started, sorta like if you have a low battery, but i've only had this battery a few months and i've done a few highway runs so i know it would have good charge (and it's not doing 'slow' starter motor sounds).

What could this be? I've tried searching for a few terms but can't find anything helpful.

Thanks :D

[/quote

Battery could be too low of CCA capacity. Try fitting a known good larger battery out of another vehicle to see if it changes on crank. I would still put my money on the battery regardless of age.

as has been said, could be the battery not having enough amps, or it could be a fuel or spark issue. if you haven't changed the plugs in a while, might be worth replacing them (doesn't hurt and they are pretty cheap at only a few dollars each)

how about new injectors or spark plugs? had them changed recently?
as has been said, could be the battery not having enough amps, or it could be a fuel or spark issue. if you haven't changed the plugs in a while, might be worth replacing them (doesn't hurt and they are pretty cheap at only a few dollars each)

Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

It could yea. did your fuel pressure get changed? what injectors do you have now? If you got a new turbo etc you must have already upgraded them? What turbo did you get?

try the obvious first and charge your battery before worrying too much about other things though.

Maybe with your new tune/setup your spark plugs are struggling a bit.

Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

yes its your fuel pump that is causing the "problem"

try turning your ignition on without starting the car... allow the pump to prime and put pressure in the rail and then try and start

should start first time :D

Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

spark plugs wear out over time and injectors get dirty. might be worth just pulling a few plugs out to have a look at them and see if they look like they are fouling up at all.

was it doing it before the fuel pump went in or did it start just after?

as has been said, make sure you give the pump time to prime before turning over. if you are and it still doesn't start easily then you can pretty much rule out the pump as it shouldn't affect things once primed.

yes its your fuel pump that is causing the "problem"

try turning your ignition on without starting the car... allow the pump to prime and put pressure in the rail and then try and start

should start first time :P

spot on, this was exactly how my car needed to be started after putting in an uprated fuel pump.

turn your car to acc, wait a sec then try turning it over.

Did you install a check valve on the fuel pump. If not, when you turn the pump off all the fuel will flow back through the pump back into the tank. So when you go to start it next time there will be no pressure in the lines. Install a check valve or you will need to prime the pump a few seconds more than normal before you start the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...