Jump to content
SAU Community

R33 Takes Long Time To Start

islade

By islade,
in General Maintenance

 Share

Recommended Posts

islade Rising Star

islade

Posted
Posted

Hey guys,

I've noticed recently that my car takes a long time to start.

I've put on a turbo, intercooler, had a quick tune at gavin woods, so somewhere in there something has happened.

Everything works perfectly, but i used to turn the key for a quarter of a second and get it started, now i'm sitting there for a few seconds while the starter motor keeps trying to get it started, sorta like if you have a low battery, but i've only had this battery a few months and i've done a few highway runs so i know it would have good charge (and it's not doing 'slow' starter motor sounds).

What could this be? I've tried searching for a few terms but can't find anything helpful.

Thanks :D

Link to comment
https://www.sau.com.au/forums/topic/278922-r33-takes-long-time-to-start/
Share on other sites
Skyspeed33 Apprentice

Skyspeed33

Posted
Posted

Hey guys,

I've noticed recently that my car takes a long time to start.

I've put on a turbo, intercooler, had a quick tune at gavin woods, so somewhere in there something has happened.

Everything works perfectly, but i used to turn the key for a quarter of a second and get it started, now i'm sitting there for a few seconds while the starter motor keeps trying to get it started, sorta like if you have a low battery, but i've only had this battery a few months and i've done a few highway runs so i know it would have good charge (and it's not doing 'slow' starter motor sounds).

What could this be? I've tried searching for a few terms but can't find anything helpful.

Thanks :D

[/quote

Battery could be too low of CCA capacity. Try fitting a known good larger battery out of another vehicle to see if it changes on crank. I would still put my money on the battery regardless of age.

mad082 Grand Master

mad082

Posted
Posted

as has been said, could be the battery not having enough amps, or it could be a fuel or spark issue. if you haven't changed the plugs in a while, might be worth replacing them (doesn't hurt and they are pretty cheap at only a few dollars each)

islade Rising Star

islade

Posted
  • Author
Posted
how about new injectors or spark plugs? had them changed recently?
as has been said, could be the battery not having enough amps, or it could be a fuel or spark issue. if you haven't changed the plugs in a while, might be worth replacing them (doesn't hurt and they are pretty cheap at only a few dollars each)

Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

GT-RZ Community Regular

GT-RZ

Posted
Posted

It could yea. did your fuel pressure get changed? what injectors do you have now? If you got a new turbo etc you must have already upgraded them? What turbo did you get?

try the obvious first and charge your battery before worrying too much about other things though.

Maybe with your new tune/setup your spark plugs are struggling a bit.

SimonR32 Grand Master

SimonR32

Posted
Posted
Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

yes its your fuel pump that is causing the "problem"

try turning your ignition on without starting the car... allow the pump to prime and put pressure in the rail and then try and start

should start first time :D

mad082 Grand Master

mad082

Posted
Posted
Injectors and Spark Plugs haven't been touched since it was working fine a month ago.

I've put in a bosch 040 pump, could that have changed anything?

spark plugs wear out over time and injectors get dirty. might be worth just pulling a few plugs out to have a look at them and see if they look like they are fouling up at all.

was it doing it before the fuel pump went in or did it start just after?

as has been said, make sure you give the pump time to prime before turning over. if you are and it still doesn't start easily then you can pretty much rule out the pump as it shouldn't affect things once primed.

thommo Mentor

thommo

Posted
Posted
yes its your fuel pump that is causing the "problem"

try turning your ignition on without starting the car... allow the pump to prime and put pressure in the rail and then try and start

should start first time :P

spot on, this was exactly how my car needed to be started after putting in an uprated fuel pump.

turn your car to acc, wait a sec then try turning it over.

shotter Rising Star

shotter

Posted
Posted

Did you install a check valve on the fuel pump. If not, when you turn the pump off all the fuel will flow back through the pump back into the tank. So when you go to start it next time there will be no pressure in the lines. Install a check valve or you will need to prime the pump a few seconds more than normal before you start the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...