Jump to content
SAU Community

Recommended Posts

Hey there guys,

I've been looking to buy a front bar for my car for.. ages.

Viva Garage has two to pick from (Masa and Dolphin clones) - 300 + (180 shipping) for the front bar.

Blits has the dolphin replica + dolphin sideskirts - 450 + 330 + (315 shipping).

The question I'm asking is; has anyone purchased and fitted a Stagea kit from either of these vendors? I'm concerned about the quality and fit.

Obviously the cost savings of Viva are tempting, but if it's going to cost me 100-200 more at the painters then the savings go out the window.

If anyone can give me their 2c I'd be grateful.

- Dervish

Link to comment
https://www.sau.com.au/forums/topic/279367-front-bar-verdict/
Share on other sites

Hi Dervish,

from the reading I have done, most people have had a lot of trouble with fitment of there products. It involved cutting, filling and from the sounds of it heaps of work to get a suitable fit. I personally haven't purchased from Viva, but I know a few people from South Australia have purchased those front bars. Im pritty sure RubyRS4 from the South Australian pages would be someone to give you a little more advice. Pritty sure he purchased one a few months back.

Goodluck with your decision.

I brought the viva masa copy i didnt not fit it myself took it somewhere to git fitted. I brought the whole kit the guy that fitted said there was no problems with the front bar and the side skirts wasn't much hassle but the rear bar he had to cut and add to it by qiute a bit.

So the front bar does fit quite well and no cutting was needed.

Edited by mrRS4

I have the ViVa Masa copy rear bar and side skirts. To put it politly, what a heap of shit!

I spent approx 25-30hrs modifing the rear bar to fit. Cut it into 3 pieces, and extended it 20mm on both sides.

Both side skirts were too short as well and had to be extended. Another 10 hours work

Plus the there is hardly any fibreglass, mainly resin, so they are weak and heavy. Typical chinese made copy crap.

Full of pin holes, bubbles and low and high spots. (Have I convinced you yet?)

The Blits stuff is made here on the Gold Coast to alot higher standard and fitment. Not sure if they still have their moulds and make it themselves, or they did sell most of their moulds to DMD the Image.

When I spoke with them last, they were telling me they got offered chinese made copy kits. They could buy front bars for $39 landed from china!! Gives an idea on the profit margin on cheap imported kits. They declined the offer as there is way too much time to get them to fit.

I have the ViVa Masa copy rear bar and side skirts. To put it politly, what a heap of shit!

I spent approx 25-30hrs modifing the rear bar to fit. Cut it into 3 pieces, and extended it 20mm on both sides.

Both side skirts were too short as well and had to be extended. Another 10 hours work

Plus the there is hardly any fibreglass, mainly resin, so they are weak and heavy. Typical chinese made copy crap.

Full of pin holes, bubbles and low and high spots. (Have I convinced you yet?)

The Blits stuff is made here on the Gold Coast to alot higher standard and fitment. Not sure if they still have their moulds and make it themselves, or they did sell most of their moulds to DMD the Image.

When I spoke with them last, they were telling me they got offered chinese made copy kits. They could buy front bars for $39 landed from china!! Gives an idea on the profit margin on cheap imported kits. They declined the offer as there is way too much time to get them to fit.

Oh yes i did forget to say that i had to return one front bar due that problem of pin holes. My side skirts i was told were ok.

I've heard the same about Viva Garage stuff. Blits quality is very good, but as you may have read, their turnaround time is farcical: I've been waiting over 5 months for my "3 day job" to be finished, and have decided to go elsewhere. If they got their customer service sorted, Blits could be great. Unfortunately, if you need them to do the fitting, you'll be a grandparent before it gets done. HOWEVER, if you're only getting them to supply the parts, then you'll be front of the line, and should end up with a very good quality product!

Your call i the end, but I can't recommend them based on their very poor service...

I brought the viva masa copy i didnt not fit it myself took it somewhere to git fitted. I brought the whole kit the guy that fitted said there was no problems with the front bar and the side skirts wasn't much hassle but the rear bar he had to cut and add to it by qiute a bit.

So the front bar does fit quite well and no cutting was needed.

After seeing this dudes rear bar fitment, Id probably never buy a viva body product. The rear bar is shocking. Where did you get it fitted?

After seeing this dudes rear bar fitment, Id probably never buy a viva body product. The rear bar is shocking. Where did you get it fitted?

A place in lonsdale called ave and no it aint that dodge one that was on today tonight a while ago yere they guy said he has never seen such a shit fitment think in the end up having to add about 30 mm to the right side of the rear bar. I will be defiantly not be buying any body parts from viva again. Just wierd that one part of the kit fitted quite well(front bar) one of the skirts but then the rest didnt. The cut out for the exhaust is also f@%ked they have got that wrong the exhaust leans on the rear bar.

Once i get some cash saved up i will be looking at getting the blits rear bar and possibly skirts.

  • 2 weeks later...

Just ordered the front bar and sideskirts from BLITS today.

Instead of charging 450 + 330 + (315 shipping), I got both pieces for 700 + 290 shipping.

There's an 'August special on', just a heads up =)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...