Jump to content
SAU Community

Recommended Posts

OK, just wondering if anybody has any advice, but this might be one for good ol' Chris Rogers.

So I picked my car up from compliance today. They fitted a new immobiliser as required under the ADRs (FYI its one of those proximity ones). I believe my car also has a factory immobiliser (as there is a red light under the clock), not sure if its standard or not.

Anyway, sometimes the car will not start. It does not get any fuel. The only way to get it to start is to turn the key completely into the OFF position, and then try to start her again. and again. and again. eventually it gets fuel and fires up.

Any suggestions on where I should start looking? Is there a proceedure i'm somehow missing?

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/279598-trouble-starting/
Share on other sites

Thanks Rianto.

I've ruled out the battery, and i dont think its the fuel pump.. im leaning towards something like one of the immobilisors nt disarming.

The times when it does start, it starts right after turning the key.

When it does NOT start, the starter motor keeps on going and going but no love.

You might hear it tomorrow (or perhaps i should leave the motor running...)

p.s. i assume all four wheels can be squeezed into the V35?

err, maybe immobiliser problem. from how Chris did my car he completely rip out factory immobiliser and put in the ADR one.

he said something about the factory immobiliser is going to give you grief soon or later, probably if they just piggy back the ADR one on top of the factory one that's probably the main source of your problem....

but just let Chris give his insights... or you can take it to him when he is down here sometime August...

wheels - wise, never done it before but I think if you take off the boot floor and leave your spare at home, you can get either 1 or 2 in the boot,

2 in the back seat, and 1 in the front passenger seat, but with all those plastic dashboard parts I hate to see your interior get scratched.... or you make 2 trips, since you're so close in sunshine....?

spider?????

Oh no!!!!!!!!!!!

INCY!!!!!!!!!!!! my pet spider........... that's where you've been hiding.............!

no, just kidding LOL

lucky it wasn't any bigger, we had palm size lunging around the house from time to time ...

good luck with VicRoads....

I had to make 3-4 return trips when I was trying to register mine due to the fact each of the 3 ladies behind the counter on different days had different concept of how to register an import, until a bloke was taking care of my case and it just went absolutely smooth in under 1 hour time!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...