Jump to content
SAU Community

A'pexi Bolt On Turbo And Suction Kit + Injectors

Bliksem
 Share

Recommended Posts

Bliksem Veteran

Bliksem

Posted
Posted

A'PEXi Turbo Model AX53B70 P25 (Basically an equivelant to a HKS GTRS) Have had the exhaust housing ceramic coated in black to keep temps down.

20,000kms old Purchased through Greenline 2 years ago. Still as good as new no shaft play ready to bolt on. Selling as I have changed to a GT35R, will also throw in a custom stainless dump pipe.

$1650

CIMG1984.jpg

CIMG1988.jpg

A'PEXi Super Suction Kit

Aluminium Hard pipe to replace the rubber intake hose between the AFM and the turbo, Hard to find.

$180

CIMG1985.jpg

Also Have a set of 6 S15 injectors 470cc purchased from Deatschwerks also 20,000kms old Asking $380

All items located in Griffith NSW. Willing to post.

Bliksem Veteran

Bliksem

Posted
  • Author
Posted

I made 250kw at 14psi, turbo is rated at 380ps, so capable of more. Trent as Status tuning told me he has seen these make close to 300kw on an SR20.

I have since discovered I have a large exhaust restriction which would have been limiting the potential of this turbo on my setup.

sparco33 Contributor

sparco33

Posted
Posted
I made 250kw at 14psi, turbo is rated at 380ps, so capable of more. Trent as Status tuning told me he has seen these make close to 300kw on an SR20.

I have since discovered I have a large exhaust restriction which would have been limiting the potential of this turbo on my setup.

pm sent for injectors. will buy.

john-e boi Mentor

john-e boi

Posted
Posted (edited)

definantly consider the Super Suction kit sold if falls through. also interested in the turbo, straight bolt on? is there everything needed to bolt onto a rb25det? will take both off you if possible. thanks

Edited by john-e boi
colesy_skyline r32 Enthusiast

colesy_skyline r32

Posted
Posted

hey mate.. i am interested in the injectors..

i want them for my r32 gtst..

will the fit straight into standard rail??

and will i need resister pack??

please pm me and let me know - am very keen

ben

JKR-32 Proficient

JKR-32

Posted
Posted

if ur 32gtst is still an rb20, then no, they wont fit ur standard rail. s15 injectors are side feed like rb25's. rb20 and rb 26 are top feed.

ps. i'm keen on the injectors.. would u do cod? as i'm in brisbane.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...